LAWO V_pro8 Installation & Operation Manual Download Page 17

Page: 17 / 109

V_pro8 Manual

V1.0/2

Installation & Configuration
Computer System Requirements

Computer System Requirements

To control parameters you will need an external computer, connected to the

pro8

via its Local Area

Network port (

LAN 1

) and running a web browser session.

Your computer

MUST

meet or exceed the following requirements:

Network Interface Card

: operating at a speed of 100 or 1000 Base-TX LAN. A minimum

speed of 100 Mbit/s is recommended for video thumbnail streaming.

Web Browser

: Mozilla Firefox, Google Chrome or Apple Safari (V6.0). Note that the

Status ->

MADI

menu is slow when using Safari.

Screen Resolution

: >= 1440 x 900 is recommended, in order to view the full operating

window without scrolling.

Summary of Contents for V_pro8














































































































Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands

LAWO V_pro8, Installation & Operation Manual

Search results

Summary of Contents for V_pro8

Reviews:

Related manuals for V_pro8

Brands by name

Popular brands