background image

 

 

22 

 

 

 
 
 
 
Every 100 hours 

 

Change the engine oil. 

 

Remove the engine shrouds and clean cooling fins. 

 

Grease the front caster pivots. 

 

Grease the jackshaft bearings. 

 

Grease the tine shaft bearings. 

 

Grease the wheel bearings 

 

Grease the control pivots. 

 

Grease the tine assembly idlers. 

 

Every 160 hours 

 

Check the spark plugs. 

 

 
Every 250 hours 

 

Replace the primary air cleaner element – check secondary air cleaner element; replace if 
dirty. (May need more often under severe conditions. See the engine manual for additional 
information). 

 

Change the hydraulic transmission filter and fluid. 

 

 
Every 500 hours 

 

Replace the secondary air cleaner element. (May need more often under severe conditions. 
See the engine manual for additional information). 

 

Change the auxiliary hydraulic reservoir fluid. 

 

Monthly 

 

Check the battery charge. 

 

Periodic Maintenance

 

Check Engine Oil Level

 

Service Interval: Before each use or daily

 

1.

 

Stop engine and wait for all moving parts to 

stop. Make sure unit is on a level surface. 

2.

 

Check with engine cold. 

3.

 

Clean area around dipstick. Remove dipstick 

and wipe oil off. Reinsert the dipstick and push 

it all the way down into the tube. 

Do Not

 

screw into place. Remove the dipstick and read 

the oil level. 

4.

 

If the oil level is low, wipe off the area around 

the oil fill cap, remove cap and add oil to the 

“FULL” mark on the dipstick.  Refer to the 

Engine Owner's manual for recommendation. 

Do Not

 overfill. 

Important:

 Do Not operate the engine with 

the oil level below the “LOW” (or “ADD”) 

mark on the dipstick, or over the “FULL” 

mark. 
 
 

Check Battery Charge

 

Service Interval: As required 

WARNING

 

CALIFORNIA 

Proposition 65 Warning 

The engine exhaust from this product 

contains chemicals know to the State of 

California to cause cancer, birth defects, or 

other reproductive harm. 

Allowing batteries to stand for an extended period 

of time without recharging them will result in 

reduced performance and service life. To preserve 

optimum battery performance and life, recharge 

batteries in storage when the open circuit voltage 

drops to 12.4 volts. 

Note:

  To prevent damage due to freezing, battery 

should be fully charged before putting away for 

winter storage. 
Check the voltage of the battery with a digital 

voltmeter. Locate the voltage reading of the 

battery in the table and charge the battery for the 

Summary of Contents for TA3016KAF1





































Reviews: