background image

5

      • Always switch off the engine before filling. Always open the filler cap with care, so any excess

        pressure present can be relieved slowly and no fuel sprays out. The work with the equipment 

        causes high temperatures on the housing. The equipment must therefore be allowed to cool 

        before filling. Otherwise, the fuel could ignite and cause serious injuries.

      • When filling with fuel, ensure that the tank is not overfilled. If liquid misses, this must be 

        cleared away immediately and the equipment cleaned.

      • After filling, ensure that the seal screw is sitting properly in order to prevent it from coming 

        loose as a result of the vibrations caused during the work.

      • Watch out for leaks. Do not start the engine if fuel is leaking. Risk of death as a result 

        of burns!

14. Usage duration and breaks. Prolonged use of the motorised equipment can cause circulation  

      disorders in the hands as a result of the vibration. However, the usage duration can be 

      extended with suitable gloves or regular breaks. Be aware that personal tendency to poor 

      circulation, low external temperatures and high gripping forces will reduce the usage duration 

      when working.

15. Be aware of damaged parts. Before initial operation and after severe impacts, check the 

      equipment for signs of damage and wear. Are individual parts damaged? In case of slight 

      damage ask seriously whether the tool will nonetheless work properly and safely. Ensure 

      correct alignment and adjustment of moving parts. Do the parts interlock correctly? Are parts 

      damaged? Is everything correctly installed? Are all the other requirements in place for proper

      functioning? Damaged safety devices etc must be repaired or replaced by authorised people if 

      there is no explanation otherwise in the operating instructions. Defective switches must be 

      replaced by an authorized body. If repairs are required, please contact a customer service 

      centre authorized by us.

16. Always switch off the engine before undertaking adjustments or maintenance work. This 

      particularly applies for work on the cutting head. 

17. Use only authorised parts. In case of maintenance and repair, use only identical spare parts. 

      Contact the service centre for spare parts.

      Warning!

 

The use of other mowing heads as well as accessories and attachments 
that are not explicitly recommended can result in danger to people and 
objects. The tool is to be used only for the intended purpose. Any 
misappropriation is regarded as improper use. The user alone – and 
definitely not the manufacturer – is responsible for property and personal 
damage resulting from such improper use.
The manufacturer cannot be held liable if machines from the same are 
modified or used improperly and damage occurs as a result.

Summary of Contents for LK PBT3043 AUTO


































Reviews: