background image

6

3329-170

Charging the Battery

Refer to Charging the Battery on page 14.

Before Operating

Danger

Gasoline is extremely flammable and explosive. A fire or explosion from gasoline can
burn you and others.

To prevent a static charge from igniting the gasoline, place the container and/or
mower directly on the ground before filling, not in a vehicle or on an object.

Fill the tank outdoors when the engine is cold. Wipe up spills.

Do not handle gasoline when smoking or around an open flame or sparks.

Store gasoline in an approved fuel container, out of the reach of children.

Warning

Adjusting the cutting height may bring you into contact with the moving blade, causing
serious injury.

Stop the engine and wait for all moving parts to stop.

Do not put your fingers under the housing when adjusting the cutting height.

Filling the Fuel Tank

Fill the fuel tank with fresh unleaded regular gasoline
from a major name-brand service station.

Important: To reduce starting problems next season,
add fuel stabilizer to the fuel all season, mixing it with
gasoline less than 30 days old.

1/2 in. (1 cm)

m-5570a

m-6587

Checking the Engine Oil
Level

1.

Remove the dipstick, wipe it clean, and fully

install the dipstick.

m-6588

m-6587

2.

Remove the dipstick and check the oil level. If the

oil level is below the Add mark on the dipstick,
slowly pour oil into the oil fill tube to raise the oil level
to the Full mark on the dipstick. Do not overfill.
(Max. fill: 20 oz., type: SAE 30 detergent oil with an
API service classification of SF, SG, SH, or SJ.)

3.

Install the dipstick.

Summary of Contents for 10356, 10357, 10358

















Reviews: