![background image](http://html2.mh-extra.com/html/lavor/tucson/tucson_manual_4086013020.webp)
(if fitted)
Machines equipped with Total Stop:
- When the machine is working, by releasing the
gun lever, the motor stops automatically to
prevent component wear during the pump by-
pass phase (motor in stand-by).
- By pressing the gun lever the motor starts au-
tomatically.
•
WARNING:
do not leave the stand-by mode
active for more than 5 minutes.
- At the end of the operation, set the switch to
“OFF”.
(if fitted)
Machines equipped with delayed, low-voltage
Total Stop:
- When the machine is working, by releasing
the gun lever, after approximately 15 seconds
the motor stops automatically to prevent com-
ponent wear during the pump by-pass phase
(motor in stand-by).
- By pressing the gun lever the motor starts au-
tomatically.
•
WARNING:
do not leave the stand-by mode
active for more than 5 minutes.
- At the end of the operation, set the switch to
“OFF”.
IMPORTANT:
(pict.11). It is advisable to put
on the safety of the pistol trigger whenever the
machine is stopped, in order to avoid uninten-
tional starting.
- Any automatic start of the machine with-
out pressing the gun trigger is attribut-
able to air bubbles in the water or other
similar phenomena which do not imply
the existence of any defects in the ma-
chine.
- Please check that the coupling of the high
pressure hose with the appliance and the
gun supplied as standard equipments made
correctly, that is to say without any water
leak.
> PRESSURE REGULATOR
If the appliance is equipped with a pressure
regulator:
- when the pressure is set to minimum the
T.S.may not trigger. Therefore, do not allow the
appliance to function in by-pass for more than
1 minute.
- do not act on the gun lever too frequently (this
may cause a malfunction).
> INSTALLATION
-
(0)
(pict.4) Check that the master switch is
turned to “OFF” and that the water filter is fit-
ted into the pump’s inlet pipe (pict.5 pos.
⑤
).
- (pict.5 pos.
⑩
) Screw the snap connection into
place by hand, without the aid of tools.
- Connect the water supply hose to the snap
connection. The hose must have an inside di-
ameter of at least 13 mm (1/2”).
- (pict.6 pos.
④
)
Connect the high pressure hose
to the pump’s outlet pipe. Press the high pres-
sure hose coupling fully down and then screw
into place by hand without the aid of tools.
- (pict.7) Connect the high pressure hose to the
gun.
- Turn the water tap fully on. The water tempera-
ture absolutely must be below 40°C.
IMPORTANTE:
The washer machine has to
operate with clean water in order to avoid any
damages to the washer machine itself.
- (pict.11)Release the gun safety catch and keep
the trigger pressed, allowing the water to flow
until all the air has been expelled.
- (pict.8) Fit the lance into the gun.
- Fit the nozzle into the lance.
- Connect the plug to the power socket.
> 1ST START-UP
When starting up for the first time or after a long
period out of use, connect the intake line only
for a few minutes so that any dirt is vented from
the delivery outlet
> START-UP
IMPORTANTE:
(pict.12,13) Whenever using
the high-pressure cleaner, users are urged to
hold the gun in the correct position, with one
hand on the grip and the other on the spray
rod.
- To start the machine, press the gun trigger
and at the same time turn the master switch to
“ON”
> DETERGENT SUCTION
(pict.3, pos.
⑧
) Fill up the detergent tank with
the suggested products, suitable for the kind of
washing to be carried out .
CORRECT USE OF THE MACHINE
- The cleaner must be placed on a firm, stable surface and must be horizontal.
- In case of operation indoors, adequate ventilation and gas venting must be assured.
- Whenever using the high-pressure cleaner, users are urged to hold the gun in the correct position, with one
hand on the grip and the other on the spray rod.
- The water jet must never be pointed at the electrical cables or at the machine.
EN
20
Summary of Contents for TUCSON
