manualshive.com logo in svg

LAVAMAC GA120L, Installation Operation & Maintenance

Share
Download
LAVAMAC GA120L Installation Operation & Maintenance Download Page 80

Maintenance

  Part No. 70476501ENR7

  80

Maintenance

 Daily

1.   Inspect the area surrounding tumble dryers, remove all

combustible materials, including lint, before operating the
machines.

2.   Check cylinder for foreign objects to avoid damage to

clothing and equipment.

3.   Clean lint from lint compartment and screen to maintain

proper airflow and avoid overheating.

WARNING

To reduce the risk of serious injury, do not
open the lint panel while the tumble dryer is
in operation. Before cleaning the lint screen,
open tumble dryer door and allow cylinder to
completely stop.

W410R1

a.

Open the lint panel.

b.

Remove all accumulated lint in the lint compartment
area. Lightly brush any lint that may be left on the lint
screen.

c.

Be sure the lint screen is not torn.

d.

The lint screen is designed to completely cover the
entire opening in the lint screen panel. Be sure that it
does so.

e.

Wipe lint off of the cabinet high limit thermostat and
thermistor. Refer to  Figure 46  .

f.

Replace the lint compartment panel on the tumble dryer
ensuring a tight fit, and lock if applicable.

4.   At end of day, clean the machine's top, front and side panels

with mild detergent. Rinse with clean water. DO NOT use
products that contain alcohol on the control panel.

NOTE: The cabinet high limit thermostat is located
on the rear of the machine near the fan.

1   Thermistor

2   Lint Screen

Figure 46

 Monthly

1.   Remove lint and debris from inside exhaust duct to maintain

proper airflow and avoid overheating.

a.

Remove external duct and duct access covers, if
present.

b.

Clean inside of duct with a vacuum.

c.

Clean dampers and make sure they operate freely.

2.   Ensure even lint distribution over lint screen.

3.   Carefully wipe any accumulated lint off the cabinet high

limit thermostat and thermistor, including perforated cover.

4.   Clean lint and debris buildup from blower to maintain

proper airflow.

 Quarterly

1.   Use a vacuum to clean air vents on drive motors.

2.   Use a vacuum to clean lint from rear limit thermostat cover.

3.   Check and clean steam coils, if applicable.

4.   Check flow of combustion and ventilation air.

5.   Check belt tension and condition. Replace worn or cracked

belts.

 Bi-Annually

1.   Check mounting hardware for any loose nuts, bolts or

screws.

2.   Check gas connections for leakage.

3.   Check for loose electrical connections.

Summary of Contents for GA120L






















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands