background image

1-877-528-6249

www.launchtechusa.com

1820 S. Milliken Ave 
Ontario, CA 91761

III

.

CRP 12

X

 

Premium

General Notice

 

Other product names used herein are for identification purposes only and may be trademarks of their respective owners. LAUNCH disclaims 

any and all rights in those marks.

 

There is a possibility that this unit is inapplicable to some of the vehicle models or systems listed in the diagnosis section due to different 

countries, areas, and/or years. Do not hesitate to contact LAUNCH if you come across such questions. We are to help you solve the problem 

as soon as possible.

Disclaimer

To take full advantage of the unit, you should be familiar with the engine.

 

All information, illustrations, and specifications contained in this manual are based on the latest information available at the time of publication. 

The right is reserved to make change at any time without notice.

 

Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs or expenses incurred 

by purchaser or third parties as a result of: accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this 

unit, or failure to strictly comply with LAUNCH operating and maintenance instructions.

 

LAUNCH shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those 

designated as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH.

Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the CRP12X Premium, please read this user’s manual first carefully and observe the 

following safety precautions at a minimum whenever working on a vehicle:

 

Always perform automotive testing in a safe environment.

 

Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could 
cause a fatal accident.

 

Wear safety eye protection that meets ANSI standards.

 

Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.

 

Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.

 

Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.

 

Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous 

voltages when the engine is running.

 

Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.

 

Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.

 

Don’t connect or disconnect any test equipment while the ignition is on or the engine is running.

 

Keep the CRP12X Premium dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the CRP12X 
Premium, when necessary.

Summary of Contents for Premium CRP 12 Series





















Reviews: