Lauda Proline RP 1290 C, Operating Instructions Manual

Page: 35 / 120

Proline Edition X cooling thermostats
YACE0100 / October 4, 2018
Starting up
35
7.5 "Master" menu structure
2 dots in the display, e.g.
MNEmv
, indicate
that a submenu follows.
3 dots in the display, e.g.
MNpfv
, indicate
that a module submenu follows.
2%32
Actual bath temperature
or actual value of
external temperature
SEt Set setpoint
Section 7.7.1
Pu Pump power
Section 7.7.3
Con Control Int/Ext
Section 7.7.4
MNEmv Settings
MNpfv Conf. Modules
SEC Protection system
C0MN Command
C00l Cooling system
AnA Analog module
Section 8.4
rS Conf. RS-232/485
Section 8.3
d1b Conf. digit. mod.
PArB. Parameters
P1d.. Control par.
Only internal or external
parameters are offered
depending on control
variable
ShoZ\ Show values
CAL.. Pt100 calibration
CAL 1 Offset int. Pt100
Section 7.8.7
dEF ! Works settgs. int. Pt
Section 7.8.8
CAL E Offset ext. Pt100
Section 7.8.9
dEF E Works settgs. ext. Pt
Section 7.8.10
UEr Software version
Section 9.2.2
Snr_H Serial number Hi Word.
Section 9.2.3
Snr_L Serial number Lo Word.
Section 9.2.3
StELL Control value of tempera.
controller. Section 9.2.4
tHEAd Temp. of housing °C
Section 9.2.4
tHS Temp. of heatsink °C
Section 9.2.4
FAn U Fan voltage in V.
Section 9.2.4
1EFF Mains curr. consumpt. in A
Section 9.2.4
U_SEC Prot. syst. voltage in V.
Section 9.2.4
U24 Act. val. 24V voltage in V.
Section 9.2.4
PU 1 Current consumpt. pump I.
Section 9.2.4
PU P Power consumpt. pump W
Section 9.2.4
PU n Pump speed rpm.
Section 9.2.4
nF 50 Mains frequency Hz
Section 9.2.4
nU Mains volt. % of rated volt.
Section 9.2.4
LE
Bath level [cm]
Section 9.2.4
tE Pt Extern temp. Pt100
Section 9.2.4
tEAnA Ext. temp. analog. interf.
Section 9.2.4
tESEr Ext.temp. RS232/485
Section 9.2.4
iSEt Curr. controller setpoint.
Section 9.2.4
SEtq. Setpoint relat. to act.
val. Section 7.8.4
S Setpoint resolution
Section 7.8.1
StArt Opern. w. mains fail.
Section 7.8.2
tih Upper temp. limit
Section 7.8.3
Cur Max. current consumpt.
Section 7.7.5
tiL Lower temp. limit
Section 7.8.3
tYPG. Detect type of unit.
Section 9.2.1
dEF Works setting
Section 7.8.5
Audjp Signal settings.
Section 7.8.6
H_All Counter operating hours
Master complete
H_PU Counter operating hours
Pump
td Int. damping time (Td)
Section 7.13.1
_P Int. proport.range (Xp)
Section 7.13.1
tn Internal reset time (Tn)
Section 7.13.1
tu Int. derivative time (Tv)
Section 7.13.1
tud Int. contr. par. auto/man.
Section 7.13.1
dEF Works settings
Section 7.13.1
iP External P-controller (Xpf)
Section 7.13.2
Ev Ext. derivative time (Tve)
Section 7.13.2
Ed Ext. damping time (Tde)
Section 7.13.2
Eb Ext.propor.range (Prop_E)
Section 7.13.2
Et0L Ext.correct. var. (K)
Section 7.13.2
E Ext. contr.par. auto/ man.
Section 7.13.2
dEF Works settings
Section 7.13.2
En External reset time (Tne)
Section 7.13.2
EP Ext. prop. factor (Kpe)
Section 7.13.2