Lattice Semiconductor ECP5 Versa Technical Notes Download Page 1 | Manualshive

Page: 1 / 78

Lattice Semiconductor ECP5 Versa Technical Notes Download Page 1

www.latticesemi.com

1

TN1265_1.1

November 2015

Technical Note TN1265

© 2015 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand
or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

Introduction

ECP5

TM

and ECP5-5G

TM

devices support high-speed I/O interfaces, including Double Data Rate (DDR) and Single

Data Rate (SDR) interfaces, using the logic built into the Programmable I/O (PIO). SDR applications capture data
on one edge of a clock while DDR interfaces capture data on both the rising and falling edges of the clock, thus
doubling the performance. ECP5 and ECP5-5G device I/Os also have dedicated circuitry that is used along with
the DDR I/O to support DDR2, DDR3, DDR3L, LPDDR2 and LPDDR3 SDRAM memory interfaces.

This document discusses how to utilize the capabilities of the ECP5 and ECP5-5G devices to implement high-
speed generic DDR interface and the DDR memory interfaces. Refer to the Implementing DDR Memory Interfaces
section of this document for more information.

External Interface Description

This technical note uses two types of external interface definitions, centered and aligned. A centered external inter-
face means that, at the device pins, the clock is centered in the data opening. An aligned external interface means
that, at the device pins, the clock and data transition are aligned. This is also sometimes called edge-on-edge.
Figure 1 shows the external interface waveform for SDR and DDR.

Figure 1. External Interface Definitions

The interfaces described are referenced as centered or aligned interfaces. An aligned interface will need to adjust
the clock location to satisfy the capture flip-flop setup and hold times. A centered interface will need to balance the
clock and data delay to the first flip-flop to maintain the setup and hold already provided.

SDR Aligned

DDR Aligned

SDR Centered

DDR Centered

ECP5 and ECP5-5G

Hi

g

h-Speed I/O Interface

1
2
3
...
»

Summary of Contents for ECP5 Versa















































































Reviews:

No comments