background image

30 - PC400 Terminal Installation & User’s Guide 
 
 

Limited One-Year Limited Warranty 

 

Lathem warrants the hardware products described in this guide against defects in material and workmanship for a 
period of 

one year

 from date of original purchase from Lathem or from an authorized Lathem reseller. The 

conditions of this warranty and the extent of the responsibility of Lathem Time Corporation (“Lathem”) under this 
warranty are listed below. 

 

1.

 

This warranty will become void when service performed by anyone other than an approved Lathem 
warranty service dealer results in damage to the product. 

2.

 

This warranty does not apply to any product which has been subject to abuse, neglect, or accident, or 
which has had the serial number altered or removed, or which has been connected, installed, adjusted, 
or repaired other than in accordance with instructions furnished by Lathem. 

3.

 

This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair, 
or any expendable parts that are readily replaced due to normal use. 

4.

 

The sole responsibility of Lathem under this warranty shall be limited to repair of this product, or 
replacement thereof, at the sole discretion of Lathem. 

5.

 

If it becomes necessary to send the product or any defective part to Lathem or any authorized service 
dealer, the product must be shipped in its original carton or equivalent, fully insured with shipping 
charges prepaid. Lathem will not assume any responsibility for any loss or damage incurred in 
shipping. 

6.

 

WARRANTY DISCLAIMER AND LIMITATION OF LIABILITY: Except only the limited express 
warranty set forth above, the products are sold with no expressed or implied warranties of any kind, 
and the implied warranties of merchantability and fitness for a particular purpose are hereby 
expressly disclaimed.   No warranties are given with respect to products purchased other than from 
Lathem or an authorized Lathem reseller and any such products are purchased "as is, with all faults."  
In no event will Lathem be liable for any direct, indirect, special, incidental or consequential damages 
arising out of or in connection with the delivery, use or inability to use, or performance of this 
product.  In the event any limited remedy given herein shall be deemed to have failed of its essential 
purpose, Lathem's maximum liability shall be to refund the purchase price upon return of the product. 

7.

 

Proof of date of purchase from Lathem or an authorized Lathem reseller is required for warranty 
service on this product. 

8.

 

This Warranty grants specific legal rights. Additional legal rights, which may vary by locale, may 
also apply. 

9.

 

Should any difficulties arise with the performance of this product during warranty, or with any 
Lathem authorized service centers, contact Lathem Time at the address below. 

Lathem Time 

200 Selig Drive, SW, Atlanta, GA  30336 

404-691-0405 

www.lathem.com

 

Copyright © 2003 Lathem Time Corporation. All rights reserved. 

Revised 01-15-2008 

Document number: USG0037I

 

Summary of Contents for PayClock PC400






































Reviews: