NEW 2/19
2
X12905ES
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
CAUTION
•
AVOID
the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these de-
vices may overheat and cause a fire hazard.
•
DO NOT
route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a
fire hazard.
•
ALWAYS
place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•
NEVER
insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•
DO NOT
block, cover or obstruct air flow to or from the Fan while in operation.
•
DO NOT
use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may
create a shock hazard.
•
DO NOT
run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
•
NEVER
use a single extension cord to operate more than one Fan or other electrical device.
•
DO NOT
use this Fan if it has been damaged or is not functioning properly.
•
THIS Fan DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008)
. This Fan is not suitable for use in agricultural facil-
ities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7
(2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
•
THIS Fan DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008)
. This Fan is not suitable for use in hazardous lo-
cations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes
and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT
use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS
be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the
outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this
condition should be replaced by a qualified electrician.
ALWAYS
unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole
means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in.
ALWAYS
turn off and
unplug the Fan when not in use.
BE CERTAIN
that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no
circumstances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must
be replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC)
and all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.
DO NOT USE A THREE-PRONG TO TWO-PRONG ADAPTER. IMPROPER CONNECTION MAY CREATE THE RISK OF ELEC-
TRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
NEW 2/19
7
X12905ES
MODELO X12905
FUNCIONAMIENTO
1. Cuidadosamente retire el Ventilador de la bolsa plástica y la caja. Arme
la unidad siguiendo estas instrucciones.
2. Coloque el ventilador sobre una superficie firme y nivelada.
ADVERTENCIA:
Los tacos de plástico o hule, tales como las patas de esta
unidad, pueden pegarse a la superficie de los muebles. La unidad podría
dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes
en el acabado de ciertas superficies de muebles, incluyendo superficies
y pisos de madera.
3. Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente
en el tomacorriente.
Cuando los enchufes quedan flojos en los tomacorrientes,
pueden deslizarse parcial o completamente fuera del toma-
corriente con un leve movimiento del cable adosado. Los
tomacorrientes en este estado podrían sobrecalentarse y
representar un grave peligro de incendio; si está cubierto
por una cortina o tela, el riesgo de incendio es aún mayor.
4. Encienda el Ventilador seleccionando la velocidad deseada con la
situada al costado del Ventilador.
(Figura 1)
Figura 2
Figura 3
5. Para ajustar el ángulo vertical, presione el panel del Ventilador hacia
delante o hacia atrás hasta la posición deseada.
(Figura 2)
6. Después de apagar el ventilador, desconecte la unidad del tomacor-
riente eléctrico.
Reinicio del Disyuntor:
Se proporciona un interruptor de 10 amps como una opción de seguridad
para su Ventilador. Cuando utilice una herramienta que tenga más amperaje
del permitido, el disyuntor saltará. Para reiniciarlo, desconecte la herra-
mienta que esté provocando que el disyuntor salte y oprima el Botón De
Reinicio adyacente a los tomacorrientes del Ventilador.
(Figura 3)
Figura 1
Botón
de
Reinicio
B
R
