Rev. B 4/13
9
5592ES
Rev. B 4/13
5592ES
4
Display reflects High Heat and
Automatic Temperature Control Function
AUTOMATIC TEMPERATURE CONTROL
(Figure 3)
The automatic temperature function will only operate on "High"
heat ( ). You cannot set the temperature automatically when
the unit is in the low heat mode.
1. To set the room at a specific temperature press the ( ) or ( ) icons
to the desired temperature. The display will now reflect the ( )
and the temperature will be flashing. The Heater is now in Auto
Temperature Mode.
2. When you reach the temperature at which you want to set the
unit, the set temperature will flash several times and then the
display will return to indicate the current room temperature and
will gradually change as the room temperature changes. NOTE:
the temperature display does not indicate the temperature of
the heated air being emitted by the heater.
3. Once the room temperature reaches 2 degrees above the set
temperature, the Heater will shut off. Once the room tempera-
ture reaches 1 degree below the set temperature, the Heater
will turn back on and continue to cycle off and on to maintain
the set temperature.
4. This function will cancel if the
icon is pressed.
Automatic air sampling feature:
Functions only when the heater
is set in the automatic mode. It is normal for the heater fan to run for
approximately 15 seconds after the heater has reached the set
temperature. From this point on, the heater fan will turn on every 10
minutes for 10 seconds until the room requires additional heat.
OPERATION
(Figures 1 through 3)
The Heater may be operated by the manual controls located
on the Heater (as shown in
Figure 1
) or by your remote control
(shown in
Figure 4
).
1. Carefully remove the Heater from the bag and the carton.
2. Place the Heater on a firm, level surface.
Plastic or rubber tabs, like the feet on this unit, may stick to
furniture surfaces and/or hardwood floors. The unit may leave a
residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces.
3. Plug the cord set into a 120 V~ electrical outlet. Be sure plug
fits tightly in outlet. A loose fit will cause overheating and dam-
age the plug. Plug and cord set may feel warm during normal
usage.
4. When the Heater is initially plugged in, the red light will come
on indicating that there is power to the unit. The red light
will remain lit until the Heater is unplugged from the electrical
outlet.
5. Turn the Heater ON by pressing the
Power Icon
( )
.
6. When initially turned on, the Heater will display the cur-
rent room
temperature in º Fahrenheit. Press the ( ) and ( )
icons at the same time to change the display to º Celsius.
Pressing the same icons again will change the display back to
º Fahrenheit.The Heater will reset to º Fahrenheit after being
unplugged.
7. Upon turning the Heater on, the unit will be in HIGH heat ( ) (1500
Watts) and will display the current room temperature.
(Figure 1)
8. Pressing the ( )
Icon
at this point will set the Heater into
Low
heat mode.
9. Pressing the ( )
Icon
once more will set the Heater into
High
heat
mode.
10.To turn the Heater OFF, press the
Power Icon
( ) and
unplug the unit from the electrical outlet.
Figure 2
Figure 1
OSCILLATION
Pressing the
Oscillation Icon
( )
will allow the Heater to oscil-
late back and forth. To stop the oscillation, press the
Oscillation
Icon
( )
again. When the Heater is in Automatic Temperature
Control, the oscillation function will stop when the set tempera-
ture is reached and resume when the Heater turns back on.
Timer Function in
Low Heat
Timer Function in
High Heat and Automatic
Temperature Control
Display when initially turned on
TIMER FUNCTION
(Figure 2)
The timer function may be activated when the Heater display is in
any function or speed. This function allows you to set the length
of time the Heater will run before turning itself off, from 1 hour to
8 hours. Pressing the
Timer Button
( ) will increase the length of
time by 1 hour each time this button is pressed. After the display
reflects 8 hours, pressing the
Timer Button
( ) once more will reset
the Heater to run continuously. The Heater will turn off when the
set time has elapsed. The unit can be turned back on by pressing
the
Power Button
( ).
MODELO 5592
Tamaño Real De Tornillos
Figura 1
(4) - M5 X 13mm
(2) - M4 X 13mm
ARMADO
(Figuras 1 a 4)
Herramientas Necesarias: Destornillador de Cabeza #2 Phillips
(no incluido)
Retire cuidadosamente el Calefactor de su bolsa y caja.
Para facilitar el armado, coloque el Calefactor de manera que la
parrilla frontal y el panel de control den hacia arriba.
1. Arme la base enclavando las
Protuberancias
en los
Orificios
para Protuberancias
.
(Figura 2)
Figura 2
3. Alinee el
Conjunto de la Base
con el
Conjunto de Soporte de
Columna
. Cerciórese de que la
Muesca de Ubicación
en el
Conjunto de Soporte de Columna
quede alineada con la
Llave
en el
Conjunto de la Base (Figura 4)
. Una el
Conjunto de la
Base
al
Conjunto de Soporte de Columna
con (4) tornillos M5 X
13 mm. Jale suavemente el
Cable Eléctrico
para que no quede
holgado, y colóquelo en el
Canal Para Cable
del
Conjunto de
la Base
.
Conjunto de
la Base
Cable Eléctrico
Figura 4
Canal Para
Cable
2. Fije las mitades de la base con (2) tornillos M4 X 13 mm. Pase
el
Cable Eléctrico
por el gran orificio que se encuentra del
Conjunto de la Base
.
NOTA:
El
Canal Para Cable
en la parte
inferior de la base debe estar hacia la parte posterior del Calefactor.
(Figura 3)
Figura 3
(2) - M4 X 13mm
Cable
Eléctrico
Conjunto de
la Base
Canal Para
Cable
Protuberancias
Llave
Orificios
para
Protuberancias
Figure 3
MODEL 5592
