FUNCIONAMIENTO
Figura 1
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.
CUIDADO:
Los tacos de plástico o hule, tales como las patas
de esta unidad, pueden pegarse a la superficie de los muebles y/o
a los pisos de madera. La unidad podría dejar un residuo capaz de
oscurecer, manchar o dejar marcas permanentes en el acabado de
ciertas superficies de muebles, incluyendo superficies de madera
y/o pisos de madera.
3. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un peligro de incendio grave; si queda cubierto por
una cortina o tela, el peligro de incendio es todavía
mayor.
4.
Cuando el Calefactor se conecte por primera vez, la
Luz de
Encendido
se encenderá indicando que hay electricidad en la
unidad. La
Luz de Encendido
permanecerá encendida hasta que
el Calefactor sea desconectado del tomacorriente eléctrico.
5.
ENCIENDA el Calefactor oprimiendo el
Botón de Encendido
.
6.
Cuando se lo encienda por primera vez
, el Calefactor estará en
New 3/11
2
5309ES
New 3/11
7
5309ES
MODELO 5309
Figura 1
Botón De
Oscilación
Botón De Encendido
Botón De
Temperatura
Calor Bajo
Calor Alto
calor
Alto
(1500 vatios) en
Máx
. (La luz Alta estará encendida
permanentemente y la luz de Máximo estará titilando).
7. Oprima el
Botón de Encendido
una vez más y el Calefactor estará
en Calor
Bajo
, indicado por la luz permanente junto a
Bajo
.
8. Oprimir el
Botón de Encendido
por tercera vez APAGARá el
Calefactor.
9. Cuando el Calefactor está APAGADO, la luz roja en la parte frontal
del Calefactor permanecerá encendida hasta que el Calefactor
sea desconectado del tomacorriente eléctrico.
Función de Oscilación:
1.
Oprimir el
Botón de Oscilación
(
OSC
) le permitirá al Calefactor
oscilar hacia atrás y hacia delante. Para detener la oscilación,
vuelva a oprimir el
Botón de Oscilación
(
OSC
). Cuando el
calefactor esté en control automático de temperatura, la función
de oscilación se detendrá cuando se alcance la temperatura
fijada y reiniciará cuando el calefactor vuelva a encenderse.
Función de Temperatura
La función de temperatura automática sólo operará en calefacción
“Alta”. No puede fijar la temperatura automáticamente cuando la
unidad se encuentre en la modalidad de calefacción baja.
1. Para fijar una temperatura específica en la habitación, presione
el botón de temperatura
(TEMP)
hasta la configuración deseada.
La luz de la temperatura escogida continuará titilando hasta que la
habitación alcance la temperatura deseada. El Calefactor realizará
el ciclo de apagado y encendido para mantener la temperatura
de la habitación. Cuando se fija en MAX (Máximo), el Calefactor
operará continuamente.
1.
ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT
PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE
OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZ-
ARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
WARNING:
FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG
FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT
OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET.
2. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical
shock, or injury to persons.
3. Make certain that the room is equipped with a working smoke detector.
4. Make certain that the power source conforms to the electrical requirements of the Heater.
5. Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left
operating unattended.
6. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended
to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to defeat this safety feature.
7. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any
manner. Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
8. To disconnect Heater, turn the Heater OFF then remove the plug from outlet.
9. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
10. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire,
or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where open-
ings may become blocked.
12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the
Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord
with throw rugs, runners, or similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this
Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from
the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
14. A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or flammable liquids
are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.
This Heater is intended for general use ONLy.
15. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
16. DO NOT use Heater outdoors.
17. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined.
Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical
requirements for Agricultural Buildings.
THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
18. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable
state or local codes or standards relating to electrical requirements for Hazardous locations.
THIS HEATER DOES NOT
MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED
CONTROL DEVICES.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk
of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Heater.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND
UNPLUG HEATER BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE
HEATER IS ON OR PLUGGED IN.
SAVE THESE INSTRUCTIONS
Luz de
Encendido
