1. Coloque el ventilador sobre una superficie firme y nivelada.
ADVERTENCIA:
Los tacos de plástico o hule, tales como las
patas de esta unidad, pueden pegarse a la superficie de los muebles.
La unidad podría dejar un residuo capaz de oscurecer, manchar o
dejar marcas permanentes en el acabado de ciertas superficies de
muebles, incluyendo superficies y pisos de madera.
2. Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos en los
tomacorrientes, pueden deslizarse parcial o
completamente fuera del tomacorriente con un leve
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un grave peligro de incendio; si está cubierto por una
cortina o tela, el riesgo de incendio es aún mayor.
New 9/11
2
2084236
New 9/11
7
2084236
1. Conecte la base - desenrosque la tuerca del módulo en el
sentido contrario a las agujas del reloj, introduzca el conjunto
de cables a través del orificio de la base. Asegúrese de alinear
la llave en la Base de apoyo con la muesca de localización en
el módulo. Inserte el módulo en el agujero en la base. Pase el
conjunto de cables a través de la tuerca del módulo y enrosque
la tuerca en el sentido de las agujas del reloj hasta que quede
apretada. (Figura 1).
4. Apriete con la tuerca de protección en EL SENTIDO DE LAS
AGUJAS DEL RELOJ.
5. Deslice el aspa en el eje del motor. Alinee la ranura en el cubo
del aspa con pasador en el eje del motor. Figura 3A)
6. Para fijar el aspa, atornille la pieza giratoria en el eje
en el sentido contrario a las agujas del reloj hasta
que quede fija en el cubo del aspa.
Figura 1
2. Hale suavemente cualquier exceso del conjunto de cables y
colóquelo en el Canal de localización de los cables. (Figura 2)
3. Incline la parte superior del ventilador hacia atrás. Coloque la
rejilla trasera sobre el motor con la flecha apuntando hacia
arriba. (Figura 3)
Figura 4
Parrilla
Delantera
ARMADO
FUNCIONAMIENTO
MODEL 5132
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
1. Make certain the power source conforms to the electrical requirements of the Fan.
2. Make certain that the room is equipped with a working smoke detector.
3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,
or injury to persons.
4. To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.
5. Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING
OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE
LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6. This Fan must
NOT
be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres
where gasoline, paint or flammable liquids are used or stored.
7.
DO NOT
use Fan in or near a window. Rain may create an electrical hazard.
8. Completely assemble Fan, according to instructions, before connecting to power supply.
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
9. Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an exten-
sion cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed.
NEVER
use a single
extension cord to operate more than one Fan. Do not plug Fan into any other cord connected device, such as a power strip, cord
reel, surge protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.
10.
NEVER
operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any
manner.
11.
NEVER
insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire,
or damage the Fan. To reduce the risk of fire,
DO NOT
block or tamper with the Fan in any manner while it is in operation.
12. Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power
Cord so the Fan or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with
throw rugs, runners, or similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Fan is not intended for use in wet or damp locations.
NEVER
locate a Fan where it may fall into a bathtub or other water con-
tainer.
NEVER
use Fan where flammable liquids are used or stored.
14.
NEVER
use Fan outdoors.
15. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please
refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical require-
ments for Agricultural Buildings.
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
16. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes or standards relating to electrical requirements for Hazardous locations.
THIS FAN DOES NOT MEET THE REQUIRE-
MENTS OF NEC ARTICLE 500 (2008).
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only one way. Match wide blade of plug to wide slot. Fully
insert. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. DO NOT attempt to defeat this safety feature.
This plug is a safety feature. It contains a safety device (fuse) that should not be removed. Discard product
if the attachment plug is damaged. To reduce the risk of fire, electric shock and personal injury, DO NOT
remove, replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it
may be due to the safety device incorporated in this plug. Call 800-233-0268, Monday - Friday, between 8:00
a.m. and 5:00 p.m. Eastern. If the plug warning label is missing or damaged, call the toll free number for a
replacement label.
7
. Con la cabeza del ventilador inclinada hacia atrás y centrada,
alinee el ornamento de la rejilla delantera para que quede
horizontal. Inserte la parte inferior de la rejilla delantera en la
rejilla trasera. La pestaña en la parte inferior de la rejilla trasera
debe estar entre dos radios de la rejilla delantera. Ajuste la
parte delantera a la trasera desde la parte superior y trabaje
a ambos lados. NO SE NECESITAN SUJETADORES PARA LA
REJILLA PARA EL ENSAMBLAJE. (Figura 4)
Rejilla Trasera
Módulo
Tuerca del
módulo
Conjunto de
Cables
Llave
Muesca de
localización
Base de apoyo
Figura 2
Conjunto de
Cables
Motor
Rejilla Trasera
Figura 3
Figura 3A
Pasador
Ranura
del Cubo
Guardia
Tuerca
Hoja
Hilandero
Orificio de
colocación
del cable
Inclinacion
