Manual Purelight Series US
5 / 8
Revision: Dec-10
Technical specifications
•
Output power (in mW, at the laser):
min. - max.
Power/wavelength green
Power/wavelength red
Power/wavelength blue
Beam (ca.)
PL-1200 G
800 - 1200
>800mW 532nm
3mm/1.5mrad
PL-2000 G
1200 - 2000
>1200mW 532nm
3mm/1.5mrad
PL-3500 G
2500 - 3500
>2500mW 532nm
3mm/1.5mrad
PL-6000 G
4500 - 6000
>4500mW 532nm
3mm/1.5mrad
PL-8000 G
6500 - 8000
>6500mW 532nm
3mm/1.5mrad
PL-12000 G
9000 - 12000
>9000mW 532nm
3mm/1.5mrad
PL-20000 G
15000 - 20000
>15000mW 532nm
4mm/1.8mrad
PL-1600 RGB
1100 - 1600
>500mW 532nm
>300mW 640nm
>300mW 445nm
3mm/1mrad
PL-2600 RGB
2000 - 2600
>800mW 532nm
>550mW 640nm
>650mW 445nm
3mm/1mrad
PL-3400 RGB
2400 - 3400
>1200mW 532nm
>550mW 640nm
>650mW 445nm
3mm/1mrad
PL-4500 RGB
3400 - 4500
>1400mW 532nm
>1000mW 640nm
>1000mW 445nm
3mm/1mrad
PL-6000 RGB
4500 - 6000
>2500mW 532nm
>1000mW 640nm
>1000mW 445nm
3mm/1.2mrad
PL-8400 RGB
6500 - 8400
>2500mW 532nm
>2000mW 640nm
>2000mW 445nm
3mm/1.5mrad
PL-10900 RGB
8500 - 10900
>4500mW 532nm
>2000mW 640nm
>2000mW 445nm
3mm/1.5mrad
PL-15500 RGB
13000 - 15000
>4500mW 532nm
>4500mW 640nm
>4000mW 445nm
3mm/1.5mrad
PL-2500 RGB
Blue Beam
1550 - 2500
>400mW 532nm
>150mW 640nm
>1000mW 445nm
4mm/>1mrad
PL-5000 RGB
Blue Beam
3300 - 5000
>1000mW 532nm
>300mW 640nm
>2000mW 445nm
4mm/>1mrad
PL-8000 RGB
Blue Beam
5900 - 8000
>1350mW 532nm
>550mW 640nm
>4000mW 445nm
4mm/>1mrad
PL-16000 RGB
Blue Beam
12000 - 16000
>3000mW 532nm
>1000mW 640nm
>8000mW 445nm
4mm/>1mrad
•
Lasersources:
air-cooled DPSS laser (green all models), laser diode (red, blue with RGB models)
•
Laser class:
4
•
Modes:
ILDA, DMX 512, auto
•
ILDA:
ILDA standard Sub-D shaped 25pin connector
•
Galvos:
max 50k scanspeed (at 4°)
•
DMX 512:
18 channels
•
Patterns:
160
•
Scanangle:
set to ca. 40° optical (60° max)
•
Input voltage:
AC 110~120V or 220~240V
switchable 50/60Hz
•
Power consumption:
350W
•
dimensions:
23.6”x14.6”x16.5” (60 x 37 x 42cm)
(W x D x H)
•
Weight:
66lbs (30kg) Laser,
total:
121lbs (55kg)
(with flight case)
•
Operating temperature:
50~95°F (
10°-35°C)
•
Loudness:
<70db
Change scanner
1.
Unscrew UK M6 screws and disconnect signal
cable.
2.
Loosen M4 x 10 screw and remove galvo.
3.
Insert galvo, reconnect and fix signal cable.
4.
Rotate galvo to center projection. Fix galvo.
Adjustable mirror mounts
Loosen setscrews, then adjust with X/Y adjustable screws. Make
sure beam is centered on scanner mirrors. Adjust Z-screw
simultaneously Tighten setscrews.
When combining beams (RGB laser), first make sure the beams are
(roughly) on the same spot on the mirrors/dichros. Then use a test
pattern (e.g. rectangle) to do fine adjustment. For adjustments,
always turn output power down (if possible).
Troubleshooting
Problem
Possible reason
Damaged part
Replacement
No power
Fuse blown
Fuse
09-00-3001-01
Power supply defective
+-24V
16-03-0039-00
Music mode not working
Microphone defective
Microphone
16-03-0001-00
Control board defective
Control board
26-2A-LT12V2-00
