Manual / Bedienungsanleitung: CS-1500 RGB
Version Jan-11
3 / 10
Regularly open the device (see “cleaning” further down) to check for dust inside, or if fog fluid condenses in the
housing (if so rearrange hazer and/or laser position).
Operating temperature is 10~35
°C
. In a new installation, check after some 15-30 minutes whether the outlet
air gets too warm. Regularly check the inside for dust deposits, especially around the fans. Let laser cool off 10
minutes after 2 hours of operation, to ensure maximum lifetime for the diode.
Distance between laser aperture and projection screen should be not less than 1 meter.
Do not turn device on and immediately off again frequently.
Do not look into the laser beam directly, especially not with optical instruments.
Do not touch the device with wet hands.
When the laser diode becomes dim or broken, please contact your dealer.
When returning laser to dealer/manufacturer always use original packaging.
Maintenance should be performed every 15-day period. See “cleaning” further down.
To ensure maximum lifetime of the laser:
Don’t overheat the laser:
•
Always ensure good ventilation
•
Don’t have stage lights (especially moving heads) directed towards the laser
•
Regularly clean the fans and the interior from dust
•
In a new installation check the temperature after 30 minutes of operation
Keep the laser dry
•
Make sure fog/hazer fluid doesn’t condensate inside the laser - fog has to be in front of the laser – not
inside
•
A few days after (each new) installation, open the cover to check if fluids condensate inside
•
If fluids condensate inside, reposition the laser or fogger/hazer
Turn the device off, when not used. The diode is on, when the device is on. Even if it is not lit.
If the laser is equipped with a remote connector, connect an emergency switch to the Remote lock connector
on the backside, the switch has to interrupt the connection between pins 1 and 2 to turn off the laser. If no
emergency switch is used, insert the 9 pin dongle instead. If the laser has no remote lock, or the 9 pin dongle
is used, use an emergency switch in the mains connection.
Using the laser
Caution – use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Rigidly mount projector. Projector can be mounted in any position.
Make sure the correct voltage is used. Connect mains. Connect an emergency switch to the 9-pin connector
(Interlock connector) on the backside (pins 1 and 2). If you do not wish to connect an emergency switch,
connect the 9-pin plug instead, and use an emergency switch in the mains connection.
Open shutter and turn key to on position, the laser beam will now exit through the front opening – be careful.
Control panel
1
Main switch
2
Remote lock, connect emergency switch
3
Dip switch, mode/DMX address selection
(see below)
4
DMX 512 in/out
5
Microphone sensitivity
6
Mains connection
7
ILDA in/out
Operating modes
The following operating modes can be selected from the DIP switch on the back side of the device:
Dip switch
Mode
1,0,0,0,0,0,0,0,0,1
Automatic
0,0,0,0,0,0,0,0,0,1
Music active
X,X,X,X,X,X,X,X,X,1
DMX
“Music active”:
patterns are changed/animated to the beat of the music. Sensitivity can be adjusted at the back panel.
“Automatic mode”:
patterns are changed automatically
“DMX“:
DMX512 Mode. Use the first 9 switches to select the address:
x
x
x
x
x
x
x
x
x
1
2
4
8
16
32
64
128
256
e.g. 1000 0000 01, DMX mode address 1 (1+0+0+0+0+0+0+0+0+0)
0010 0100 01, DMX mode address 36 (0+0+4+0+0+32+0+0+0)
In music active mode the speed can be set with switches 3 and 4:
Off, off
Auto speed
Off, on
Mid
On, off
Slow
On, on
Fast speed
