Laser Technology TruSense S300 Series User Manual Download Page 28

Page: 28 / 91

LTI TruSense S300 Series Integration Manual 3nd Edition

Page 22

$MM Measurement Mode

For liquid applications $MM should always be set to 4.

IMPORTANT:

If $MM is not set to 4,

incorrect operation of sensor will occur.

Set:

Get:

$MM,

<CR><LF>

$MU<CR><LF>

Instrument Reply:

$MM,

n*CRC16

<CR><LF>

Instrument Reply:

$MM

,n*CRC16

<CR><LF>

where:

= message identifier

= mnemonic for Measurement Units
= measurement mode

0 to 2= Do not use

4 = Liquid measurement mode

*CRC16

= 16-bit CRC

<CR>

=carriage return

<LF>

= line feed

Example:

Input: Get

$MM<CR><LF>

Reply:

$MM,4*6C9A<CR><LF>

Input: Set

$MM,4<CR><LF>

Reply:

$MM,4*6C9A<CR><LF>

$MU

Change Measurement Unit

This command is used to change the measurement units. Factory default is meters and three

decimal places.

Set:

Get:

$MU,

<CR><LF>

$MU<CR><LF>

Instrument Reply:

$MU,

u,nn,K,MM*CRC16

<CR><LF>

Instrument Reply:

$MU

,u,nn,K,MM*CRC16

<CR><LF>

where:

= message identifier

= mnemonic for Measurement Units
= measurement units

0 or m = meters

1 or f = feet

= Number of places after decimal point. Max = 3

= Not used in Liquid mode.

*CRC16

= 16-bit CRC

<CR>

= carriage return

<LF>

= line feed

Example:

Input: Get

$MU<CR><LF>

Reply:

$MU,F,33,K,11*35B0<CR><LF>

Input: Set

$MU,F,3<CR><LF>

No Changes to current settings

Reply:

$MU,F,33,K,11*35B0<CR><LF>

Input: Set

$MU,M,2<CR><LF>

Changes to current settings with Banner turned on

$DB,1

Reply:

TruSense S300 Series,DS-330-1.14

Summary of Contents for TruSense S300 Series



























































































Search results

Summary of Contents for TruSense S300 Series

Reviews:

Related manuals for TruSense S300 Series

Brands by name

Popular brands

Laser Technology TruSense S300 Series, User Manual

Search results

Summary of Contents for TruSense S300 Series

Reviews:

Related manuals for TruSense S300 Series

Brands by name

Popular brands