background image

14. Care, Maintenance and Service of your LaserPerformance  

Product

Before rigging your boat, read and familiarize yourself with the rigging manual. Failure to adhere to these guide-

lines could invalidate your warranty.

Maintenance

• Keep the equipment clean by frequently flushing with fresh water. In corrosive atmospheres, stainless parts may 

show discoloration/brown staining around screw holes and rivets. This is not serious and can be removed with  

a fine abrasive. 
• Excess water should be removed from the hull. 
• Ropes, rigging and fittings should be checked at regular intervals for wear and tear, including winch gear. 
• All moving parts should be lightly lubricated to avoid jamming, i.e., McLube, dry Teflon or a dry silicone  

based spray. Do not use oil. 
• Inspect shackles, pins and clevis rings and tape up to stop snagging sails, ropes and clothing and to prevent  

them from coming undone. 
• When refastening screws do not over tighten as this may strip the thread and do not reuse Nyloc nuts more  

than three times. 
• Damaged or worn parts should be replaced. 
• Sails should be thoroughly washed down with fresh water, dried and stored in a dry place.

Trailers and Trolleys/Dollies

• It is highly recommended that a trolley/dolly is used to launch and recover your boat. Dragging your hull up onto a 

beach or slip way will wear away the gel coat or polyethylene and damage the boat. Also, the hull should not be left 

on a pebble beach as the hull skin could be dented. 
• Trailers should be rinsed with fresh water and checked at regular intervals. It is recommended that trailers be 

serviced annually. The trailer and road base should never be immersed in water. 
• Trailers and trolleys supplied by LaserPerformance are designed to transport the hull in the best possible manner 

to avoid damaging the hull. For instance, LaserPerformance does not recommend support hulls on rollers except on 

the keel line and only where there is a reinforced keelson. We also recommend gunwale hung trolleys for our small-

er products. Hulls supported by a trolley bunk or wide strap must have the ability to drain water away from the 

hull. Trolley bunks padded with carpet or foam can cause blistering in the gel coat and changes to the hull color. 

Please do not transport your LaserPerformance product on a trailer or trolley that has not been specifically designed 

for the product. Hulls damaged through using an incorrectly designed or wrongly set up trailer or trolley are not 

covered under warranty. 
• When securing your boat to a trailer for transport be very careful that ratchet straps and ropes are not over tight-

ened and that there is sufficient padding under the strap or rope to prevent the hull/deck from being damaged 

through abrasion or pressure. 
• Top covers must not be allowed to “flap” when driving at speed. This can abrade the surface of the hull and  

damage it.  It is recommended if you are towing and plan to use your top cover that an under cover is fitted first  

to prevent cover flap damage to the top sides of the hull. 
• Repairs to the polyethylene or GRP hulls should be undertaken by persons with the relevant equipment and skills. 

Contact LaserPerformance for advice.

Storage

• Your boat should always be tied down securely to the ground when not in use. 
• UV light will cause fading to some components and fittings. A cover is recommended to reduce the UV degradation. 
• Do not leave the rig under tension when not sailing or during storage. 
• Care must be taken to support the hull adequately if storing on racking or similar.  Any sustained point loading 

could permanently dent or distort the hull. 
• Under covers for LaserPerformance products should be produced from a breathable or semi breathable fabric to 

allow moisture to evaporate away from the hull. This is essential to prevent damage to the hull skin. Also, the hull 

should never be left in the under cover wet or damp. A combination of moisture and heat over an extended period 

can also damage the hull. The under cover is designed to protect the hull when being transported and should be 

removed when the hull is being stored. Typical damage includes small bubbles or blisters, excessive print through 

of glass reinforcement, foam or wood and color change.   
• Rudders and centerboards must never be stored wet in carry/combo bags. This can cause blistering, print through 

and warpage. 
• All our GRP products are designed to be dry sailed. In other words stored on dry land. If you intend to leave your 

boat on a mooring for any length of time it is essential that you apply an osmosis barrier coat. LaserPerformance 

can recommend a suitable product.

On Water Towing 

 

• Towing your LaserPerformance product at high speed (10 – 20 knots) behind a rib or power boat can seriously  

damage the hull.  Boats damaged in this manner are not covered by the warranty.  LaserPerformance recommends  

a maximum towing speed of 6 knots.

Summary of Contents for Pico



















Reviews: