manualshive.com logo in svg

Laser Key Products 3D Pro Xtreme, User Manual

Share
Download
Laser Key Products 3D Pro Xtreme User Manual Download Page 4

Page 

3

 of 

55

 

 

The Emergency Stop (On/Off) Button 

The Emergency Stop acts as the On/Off 
Switch. The “Emergency Stop Button” is 
situated on the left hand side of the machine. 
In an emergency, hit the button to turn off 
the machine. To turn the machine on, twist 
the button clockwise and it will pop out. To 
turn the machine off, press the button. Note 
that if you simply want to cancel a key 
cutting process that using the stop button on 
the software is a better option. 

 

 

 
 

Software Installation 

Installing the Software

:

 

 

1. Go to 

LASERKEYPRODUCTS.COM

 and on the right side of the main home page under Popular 

Downloads click 3D Xtreme Software. 
 
2. Next to v15 Click ‘Purchase and Download Now’ then click ‘Add to Cart’ then click ‘Checkout’ 
then provide Company and other information and click ‘Submit the Information’ and in the 
‘Discount Coupon’ box use the coupon code provided in the white envelope received with new 
machines and select ‘Use Coupon’ payment method and click ‘Continue’ and then ‘Confirm 
Order’ and then ‘Download Now’. 
 
3. The coupon Code will be in the white envelope received with new machines.  
(Contact us to purchase codes and obtain the codes download password) 
 
4. Download, extract and Run the downloaded file and follow the on screen instructions 
 

(A video of this procedure can be found on the Xtreme download page) 

Summary of Contents for 3D Pro Xtreme
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands