![background image](http://html1.mh-extra.com/html/larson-electronics/halp-24-2l-led-2xh/halp-24-2l-led-2xh_instruction-manual_676822002.webp)
HALP-24-2L-LED-2XH
Larson Electronics, LLC
Phone: (800) 369-6671
Fax: (903) 498-3364
www.larsonelectronics.com
2
of
2
INSTALLATION
1.
Install fixture to surface with four mounting brackets (mounting hardware not included).
2.
Remove lens by releasing latches that secure the lens. The lens will suspend by the tethers inside the
fixture.
3.
Remove lamps.
4.
Twist wing nuts ¼ turn counter clockwise to release the ballast tray from the housing.
5.
Electrical voltages and frequency are listed on the ballast tray for reference.
6.
For supply connections use conductors suitable for min. 90° C.
7.
Connect internal wires per wiring diagram on ballast, and according to NEC requirements.
8.
Replace the ballast tray and twist wing nuts ¼ turn clockwise to secure.
9.
Install lamps.
10.
Replace lens and secure all latches.
MAINTENANCE
Electrical and mechanical inspection of all components must be performed on a regularly scheduled basic, determined by
the environment and frequency of use. It is recommended that inspection be performed a minimum of once a year.
WARNING:
ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND
MAINTENANCE. INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND
COMPETENT ELECTRICIAN.
1.
Inspect all contact wire terminals for tightness. Discoloration due to excessive heat is an indicator of a possible
problem and should be thoroughly investigated and repaired as necessary.
2.
Inspect contacts for signs of wear and replace if necessary.
3.
Clean exterior surfaces making sure nameplates remain legible.
If any part of the light appears to be missing, broken, or show signs of damage—discontinue use immediately! This
condition could cause serious or fatal personal injury due to electrocution and/or equipment damage. Repair with the
proper replacement part(s) before continuing service.
SURFACE MOUNTING
Flange type aluminum mounts attached at each end of the fixture enables it to be simply secured to any surface. The
mounts provide some shock absorbency protection while enabling the user to simply mount the fixture with the through-hole
taps that protrude on each side of the fixture. The mounting holes are 14.91" inches on center apart along the top of this
hazardous location light. The mounting holes are 9.5" inches on center across the top of the light.
PENDANT MOUNTING
This light fixture can hang from the ceiling suspected by rigid pipe. Each fixture is equipped with either two 1/2" or 3/4" NPT
hubs on either side of the fixture. Operators will bring rigid pipe down to the threaded mounting ups. The wiring is fed down
through the rigid pipe to one of the NPT hubs and tied to the fixture`s lead wires to complete the electrical connection. The
remaining pendant hub provides support for the opposite end of the fixture.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use. Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The
HALP-24-2L-LED-2XH
is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR
WARRANTY
AND
RETURN
INFORMATION.