Lars Thrane 90-102071 User & Installation Manual Download Page 39

Page: 39 / 83

LT-3100S GMDSS User & Installation Manual Rev. 1.02

Interfaces

Lars Thrane A/S

www.thrane.eu

Page 28 of 71

LT-3140S Interface Unit

The LT-3140S Interface Unit is designed for indoor mounting and connected to the LT-3110S Control Unit
via an Ethernet cable. The LT-3140S Interface Unit specifications are available in

App. B - Specifications

page 58. Cable strain relief must be used for securing all cables connected to the LT-3140S Interface Unit.

The LT-3140S Interface Unit has the following interfaces available:

•

4 x Ethernet

•

2 x RS-422

•

4 x GPIO

•

4 x CAN

•

DC input

•

Chassis ground

The LT-3140S Interface Unit is required, if connecting to the following external equipment:

•

LT-3150S Alarm Panel

-> via CAN (up to 3 devices)

•

LT-3160S Printer Adapter

-> via CAN

•

Central Alarm Management (CAM) system

-> via RS-422 (BAM)

•

Electronic Chart Display and Information System (ECDIS) -> via RS-422 (NAV)

•

Ship Security and Alarm System (SSAS) Alarm Button

-> via GPIO (up to 3 devices)

•

Ship Security and Alarm System (SSAS) Test Button

-> via GPIO

Figure 30: LT-3140S Interface Unit.

Summary of Contents for 90-102071




















































































Search results

Summary of Contents for 90-102071

Reviews:

Related manuals for 90-102071

Brands by name

Popular brands

Lars Thrane 90-102071, User & Installation Manual

Search results

Summary of Contents for 90-102071

Reviews:

Related manuals for 90-102071

Brands by name

Popular brands