background image

V i b e r a n t   O w n e r ’ s   M a n u a l -   1

1

2

3

7

6

5

Congratulations on your purchase of a Lanzar Viberant amplifier. You have purchased a quality product designed
and engineered to give you many years of uncompromised musical service. VIBE amplifiers are designed with
the latest technology available, which provides headroom for even the most demanding peaks and dynamic ranges
found on modern CD's and recordings.

T A B L E   O F   C O N T E N T S

System Wiring

6. 2 channel stereo

7. 2 channel bridged mode

8. 2 channel tri-mode

9. 2 channel triamp system

10. 4 channel stereo

11. 4 channel bridged mode

12. 4 channel tri-mode

13. Precautions

14.Troubleshooting

15.Notes

1. INPUT LEVEL CONTROLS

Enables the matching of input levels to the output levels from
head unit (or other signal source).

2. CROSSOVER MODE SELECTOR

Determines the mode of built-in crossover:
low pass (permits only low frequency signals to pass to speakers),
high pass (permits only high frequency signals to pass to speakers),
or flat.

3. BASS BOOST CONTROL

With a bass boost switch engaged, the bass level is increased
approx 18dB.

4. REMOTE BASS BOOST

Plug in the remote bass boost control wire in here

5. POWER & PROTECTION INDICATORS

Provide instant information on status of amplifier, including
short-circuit and thermal overload alerts.

6. HIGH PASS FILTER (HPF)

When Crossover Mode Selector is in High Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 80-
2.5KHz.

7. LOW PASS FILTER (LPF)

When Crossover Mode Selector is in Low Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 35-
400Hz.

Table of Contents

Feature and Controls

1. VIBE 226/236/246/256/266/276/286

2. VIBE 416/426/436

3. Installation

4. Specifications

Fe at u r e s   a n d   Co n t r o l s

V i b e r a n t   O w n e r ’ s   M a n u a l

V I B E   2 2 6 / 2 3 6 / 2 4 6 / 2 5 6 / 2 6 6 / 2 7 6 / 2 8 6

4

Summary of Contents for VIBE226










Reviews: