SISPM1040-582-LRT Quick Start Guide
33754 Rev. E
Page
2
of
2
PoE++ Power Note
: The Meanwell 25160 (and other) power supplies are shipped set to 48VDC. If you unbox the PS, plug
it into the SISPM1040-582-LRT and then connect 60W cameras to the switch, the cameras may not power up by POE.
The SISPM1040-582-LRT needs 52-57VDC to power all 8 ports. You must use a small Phillips screwdriver to turn the PS
potentiometer up to 52-57VDC.
DIN Rail Mounting
:
Attach the DIN Rail mounting kit to the rear panel of the chassis. Insert screws and tighten with a
screwdriver. Insert the upper lip of the DIN rail into the DIN-rail mounting kit and press the switch towards the DIN rail
until it snaps into place. Make sure the switch is attached securely to DIN Rail.
Wall Mounting (Optional)
:
Attach the wall mounting plates to rear panel of the chassis. Insert screws and tighten.
Install screws on the appropriate location on the wall. Make sure that the switch is attached securely to the wall.
Installing SFP Modules
:
You can install or remove an SFP from an SFP port without powering off the switch.
Note
: The SFP ports should use UL Listed Optional Transceiver product, Rated 3.3Vdc, Laser Class 1.
Note the proper
orientation and insert the module into the SFP port. Press firmly to ensure that the module seats into the connector.
Connecting the DI/DO Relay
:
Insert the negative (ground)/positive DI/DO Relay wires into the
+
and
-
terminals,
respectively. See the
Install
Guide
for more details.
Power Connection
:
Warning
: Connect the power supply to the switch first, and then connect the power supply to
power. Otherwise product failure may occur.
1.
Verify that power is off to the DC circuit that you are going to attach to
the switch PoE DC-input connector. This can be either of two power supplies (AC-input or DC-input) or site source DC.
2.
As an added precaution, place an appropriate safety flag and lockout device at the source power circuit breaker, or
place a piece of adhesive tape over the circuit breaker handle to prevent accidental power restoration while you are
working on the circuit.
Warning
: Hot Surface; Do Not Touch.
Power Disconnection
:
To disconnect power from the
switch after a successfully boot:
1.
Turn off power to the switch.
2.
Disconnect the cables.
Connecting P1 and P2 Power Inputs
:
Insert the negative/positive DC wires into the
V-
and
V+
terminals,
respectively. Use a small flat-blade screwdriver to tighten the wire-clamp screws on the front of the
Terminal Block connector. Insert the Terminal Block connector prongs into the terminal block receptor. If
the
SYS
LED is ON, the power connection is correct. See the
Install
Guide
for more details.
Initial Switch Configuration
:
When you power up the switch the first time, the web UI displays a First
Time Wizard displays. See the
SISPM1040-582-LRT Web User Guide
for more Web UI information. See the
SISPM1040-582-LRT CLI Reference
for more CLI information.
Factory Defaults
: IP Address = 192.168.1.77,
Subnet Mask = 255.255.255.0, Default Gateway = 192.168.1.254, Username = admin, and Password = admin.
Contact Us
:
Toll Free: 800-526-8766 | Phone: 949-453-3990 | Fax: 949-453-3995 |
© 2021 Lantronix, Inc. All rights reserved. No part of the contents of this publication may be transmitted or reproduced in any
form or by any means without the written permission of Lantronix. Lantronix is a registered trademark of Lantronix, Inc. in the
United States and other countries. Patented
; additional patents pending. All other trademarks and
trade names are the property of their respective holders.