SISGM1040-284-LRT Quick Start Guide
33807 Rev. C
Page
2
of
2
Power Supply
:
ATTENTION
:
This case must be earth grounded. No DC input may be earth grounded. Use Isolated
Power Supply.
Power Connection
Warning
: Connect the power supply to the switch first, and then connect the
power supply to power; otherwise catastrophic product failure may occur.
1.
Verify that power is off to the DC
circuit that you are going to attach to the switch PoE DC-input connector. This can be either of the two power
supplies (AC-input or DC-input) or site source DC.
2.
As an added precaution, place an appropriate safety flag and
lockout device at the source power circuit breaker, or place a piece of adhesive tape over the circuit breaker
handle to prevent accidental power restoration while you are working on the circuit.
Power Disconnection
:
To disconnect power from the switch after a good boot:
1.
Turn off power to the switch.
2.
Disconnect the cables.
Various power supply models are available from Lantronix (sold separately).
Warning
: You must use an isolated
power supply for Lantronix to honor the switch warranty. Lantronix provides Power Supply 25165, Power Supply
25130, SPS-UA12DHT and PS-DC-DUAL Series. Each power supply model is described in the Install Guide.
Connecting Power
: The switch can be powered from two power supplies (input range 12V ~ 48V). Insert the
positive and negative wires into the
V+
and
V-
contacts on the terminal block and tighten the wireclamp screws
to prevent the wires from being loosened.
Note
: Make all cable connections before connecting Power.
Power Connector
(4-Pin Terminal Block):
Input
: DC 12-48V.
P1 +/-
Power Input 1 plus and minus.
P2 +/-
Power
Input 2 plus and minus.
ALM
Alarm Relay Output.
Connecting the DI/DO
(Digital Input / Digital Output) Relay:
1
. Insert the negative (ground)/positive DI/DO Relay
wires into the + and - terminals, respectively.
2
. Use a small flat-blade screwdriver to tighten the wire-clamp
screws on the front of the Terminal Block connector.
3
. Insert the Terminal Block connector prongs into the
Terminal Block receptor. See the DI/DO Use Case in the Install Guide.
Connect and Log In via CONSOLE Port
: You can log on to the switch with the
username and password. The default CLI user name and password is
admin
.
You should change the password as soon as possible.
1
. Connect a PC to the SISGM1040-284-LRT Ethernet port (RJ45 Ethernet port).
2
. In Telnet, enter the command
telnet 192.168.1.77
.
3
. Login with default Username (
admin
)
and Password (
admin
).
4
. Change the IP with the CLI commands in the CLI Reference.
Connect and Log In via Web Browser
: After initial power up, perform the initial
switch configuration using a web browser. To begin the initial configuration stage,
reconfigure your PC’s IP address and subnet mask so the PC can communicate with the
switch. After changing PC’s IP address, you can access the switch’s Web GUI using the
switch’s default IP address of 192.168.1.77. The default Subnet Mask is 255.255.255.0.
The default Username and Password are
admin
. You should change the password as
soon as possible. See the Web User Guide for configuring other switch features.
Related Documentation
: SISGM1040-284-LRT Install Guide 33808, Web User Guide 33809,
CLI Reference 33810. Release Notes (version specific).
Contact Us
: Lantronix Corporate Headquarters; 7535 Irvine Center Drive, Suite100, Irvine, CA 92618, USA.
Toll Free: 800-526-8766. Phone: 949-453-3990. Fax: 949-453-3995.
http://www.transition.com/support
. Sales Offices:
www.lantronix.com/about/contact
© 2021 Lantronix, Inc. All rights reserved. No part of the contents of this publication may be transmitted or
reproduced in any form or by any means without the written permission of Lantronix. Lantronix is a registered
trademark of Lantronix, Inc. in the United States and other countries.
Patented:
; additional patents pending. All other trademarks and trade names are the property
of their respective holders.