SISGM1040-284-LRT Quick Start Guide
33807 Rev. C
Page
1
of
2
SISGM1040-284-LRT
Hardened Managed Switch, (8) 10/100/1000Base-T +
(4) 100/1000Base-X SFP Slots
Quick Start Guide
The SISGM1040-284-LRT provides eight 10M/100M/1G RJ45 ports,
four GbE SFP ports and one RJ45 console port. SISGM1040-284-LRT
provides high performance and environment flexibility for industrial applications.
Caution
: See the Install Guide for important Safety Warnings and Cautions, Features and Benefits, Ordering
Information, Specifications, Safety Instructions, Front Panel and LED Descriptions, Installation, Grounding, DIP
Switch Settings, Power Supply information, Connecting Power, CONSOLE Port, CLI Initialization, Troubleshooting,
Compliance, Warranty, and Rapid Ring operation.
Installation
Installation involves switch mounting, grounding, cable connection, configuration, and power connection
information.
Caution
: Read “Safety Warnings and Cautions” in the Install Guide before proceeding. Verify the box
contains one Managed Ethernet Switch, one DIN-Rail Clip, three DIN-Rail Clip Screws, one Console Cable, one
Quick Start Guide, one support postcard, and one Power Supply (optional; sold and packaged separately).
Contact your sales rep if you did not receive these items. Save the packaging for possible future use.
DIN Rail Mounting
:
1
. Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
2
. Hook the
unit over the DIN-Rail.
3
. Push the bottom of the unit towards the DIN-Rail until it snaps into place.
Wall Mounting
: 1. Screw on the wall-mount plate with the plate and screws in the accessory kit. See the Install
Guide for details.
Ethernet Interface (RJ45 Ethernet)
:
The switch provides two types of electrical interfaces: RJ45 and optical (mini-
GBIC). To connect to a PC, use a straight-through or a cross-over Ethernet cable. To connect the SISGM1040-284-
LRT to an Ethernet device, use UTP (Unshielded Twisted Pair) or STP (Shielded Twisted Pair) Ethernet cables. See
the Install Guide for pin assignments.
Ethernet Interface (Fiber, SFP)
:
For a 100 Mbps fiber port available, prepare the LC connectors or SC connectors
(with the use of an optional SC-to-LC adapter). For the 1000 Mbps fiber ports, use mini-GBIC SFPs. These accept
plug in fiber transceivers that typically have an LC style connector. They are available with multimode, single
mode, long-haul or special-application transceivers. See the Install Guide for
Warnings
and
Cautions
.
Ground Screw
: The front panel grounding screw can be used for grounding. Run the ground connection from the
ground screw to the grounding surface before connecting devices.
ATTENTION
:
This case must be earth
grounded. No DC input may be earth grounded. Use an Isolated Power Supply.
RESET button
: Press to reboot the system without removing power.
DIP Switch
: The front panel RM/CPL DIP switch lets you set Ring Settings. See “DIP Switch (Ring Settings)” in the
Install Guide. Note that you can also configure Ring settings via the Web UI and the CLI.
LEDs
: See the “LED Descriptions” in the Install Guide.
Console Port
: is for local management by using a terminal emulator or a computer with terminal emulation
software. Settings: Baud rate: 115200bps. 8 Data bits, 1 Stop bit. Priority: None. Flow control: None. To connect
the host PC to the console port, an RJ45 (male) connector-to-RS232 DB9 (female) connector cable is required.
The RJ45 connector of the cable is connected to the Console port of the SISGM1040-284-LRT. The DB9 connector
of the cable is connected to the PC COM port.