manualshive.com logo in svg

Lantronix PremierWave, User Manual

Share
Download
Lantronix PremierWave User Manual Download Page 24

PremierWave® EN Embedded System on Module User Guide

24

4: Configuration Using Web Manager

This chapter describes how to configure the PremierWave EN embedded system on module using 
Web Manager, the Lantronix browser-based configuration tool. The unit’s configuration is stored in 
non-volatile memory and is retained without power. All changes take effect immediately, unless 
otherwise noted. It contains the following sections:

 Accessing Web Manager

 Device Status Page

 Web Manager Components

 Navigating Web Manager

Accessing Web Manager

Note:

You can also access the Web Manager by selecting the Web Configuration tab on 

the DeviceInstaller application window.

To access Web Manager, perform the following steps:

1. Open a standard web browser. Lantronix supports the latest versions of Internet Explorer, 

Mozilla Firefox, Safari or Chrome web browsers. 

2. Enter the IP address or hostname of the PremierWave EN unit in the address bar. The IP 

address may have been assigned manually using DeviceInstaller (see the 

PremierWave EN 

Embedded System on Module Quick Start Guide

) or automatically by DHCP. 

3. Enter your username and password. The factory-default username is “

admin

” and “

PASS

” is 

the default password. The Device Status web page displays configurations including network 
settings, line settings, tunneling settings, and product information.

Summary of Contents for PremierWave


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands