background image

 

 

  9: Services Settings 

PremierWave XC User Guide 

 

64

 

HTTP Settings

 

Description 

Logging State 

Select 

Enabled

 or 

Disabled

 for the state of the HTTP server logging.

 

Max Log Entries 

Sets the maximum number of HTTP server log entries. Only the last 

Max

 

Log

 

Entries

 are cached and viewable.

 

Log Format 

Set the log format string for the HTTP server. Follow these 

Log

 

Format

 rules:

 

 

%a

 -  remote IP address (could be a proxy) 

 

%b

 -  bytes sent excluding headers 

 

%B

 - bytes sent excluding headers (0 = '-') 

 

%h

 - remote host (same as '%a') 

 

%{h}i

 - header contents from request (h = header string) 

 

%m

 - request method 

 

%p

 - ephemeral local port value used for request 

 

%q

 - query string (prepend with '?' or empty '-') 

 

%t

 - timestamp HH:MM:SS (same as Apache '%(%H:%M:%S)t' or 

'%(%T)t') 

 

%u

 - remote user (could be bogus for 401 status) 

 

%U

 - URL path info 

 

%r

 - first line of request (same as '%m %U%q <version>') 

 

%s

 - return status 

Authentication Timeout 

The timeout period applies if the selected authentication type is either 

Digest

 

or 

SSL/Digest

.  After this period of inactivity, the client must authenticate 

again.

 

 

To Configure HTTP Settings 

Using Web Manager 

 

To configure HTTP settings, click 

HTTP

 in the menu bar and select 

Configuration

 

To view HTTP statistics, click 

HTTP

 in the menu bar and select 

Statistics

Using the CLI 

 

To enter the HTTP command level: 

 enable -> config -> http

 

Using XML 

 

Include in your file:  

<configgroup name=”http server”>

 

Table 9-5 HTTP Authentication Settings 

HTTP Authentication 
Settings

 

Description 

URI 

Enter the Uniform Resource Identifier (URI). 

Note: 

The URI must begin with ‘/’ to refer to the filesystem.

 

Summary of Contents for PremierWave XC














































































































Reviews: