Lantronix PremierWave 2050 Command Reference Manual Download Page 91 | Manualshive

Page: 91 / 428

background image

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

91

email disconnect

<number>

Sets an email profile to use to send an email alert upon
closing a connect mode tunnel. <number> = the number
of the email profile to use.

exit

Returns to the tunnel level.

flush serial disable

Characters already in the serial data buffer are retained
upon establishing a connect mode tunneling connection.

flush serial enable

Flushes the serial data buffer upon establishing a connect
mode tunneling connection.

flush start character disable

Enables forwarding of the connect start character into the
network.

flush start character enable

Disables forwarding of the connect start character into the
network.

host

<instance>

Enters the next lower level. Specify the instance for the
next lower level.

host mode sequential

Connects to the first host in the list that accepts the con-
nection.

host mode simultaneous

Selects simultaneous connections to all hosts on the host
list.

kill connection

Disconnects the active connect mode tunneling connec-
tion or connections.

local port

<number>

Sets a specific port for use as the local port. <number> =
the number of the port to use.

no email connect

Discontinues sending email alerts upon establishing a
connect mode tunnel.

no email disconnect

Discontinues sending email alerts upon closing a connect
mode tunnel.

promote host

<number>

Promotes the identified host, exchanging it place with the
host above it, to adjust the order of the defined hosts.

reconnect time

<milliseconds>

Sets the reconnect time value for tunneling connections
established by the device in milliseconds. <milliseconds>
= timeout in milliseconds.

show

Displays the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

show status

Displays tunnel connect status.

start character

<control>

Sets the connect mode start character. The character may
be input as text, control, decimal, or hex. A control charac-
ter has the form <control>C. A decimal value character
has the form \99. A hex value character has the form
0xFF.

write

Stores the current configuration in permanent memory.

connect (tunnel-connect:1) level commands

block network disable

Forwards (tunnels) network data in connect mode tunnel-
ing.

block network enable

Discards all data coming in from the connect mode tunnel
before forwarding it to the serial interface (generally used
for debugging).

block serial disable

Forwards (tunnels) serial data in connect mode tunneling.

block serial enable

Discards all data coming in from the serial interface before
forwarding it to the connect mode tunnel (generally used
for debugging).

«
...
89
90
91
92
93
...
»

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PremierWave 2050

Brand: GARDTEC Pages: 48

Brand: FAAC Pages: 64

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: IDS Pages: 2

Brand: nekos Pages: 8

Brand: nekos Pages: 8

Brand: Neles Pages: 12

Brand: T&S Pages: 5

Brand: YASKAWA Pages: 49

Brand: M-system Pages: 17

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Brand: Vag Pages: 15

Brand: Warner Electric Pages: 4

Brand: HQ Power Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands