background image

 

MatchPort b/g Integration Guide 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright and Trademark  

© 2011 Lantronix. All rights reserved. No part of the contents of this book may be 
transmitted or reproduced in any form or by any means without the written permission 
of Lantronix. Printed in the United States of America.  

MatchPort®, with its patent-pending technology, is a trademark of Lantronix. Ethernet 
is a trademark of XEROX Corporation. UNIX is a registered trademark of The Open 
Group. Windows is a trademark of Microsoft Corporation.  

Contacts 

Lantronix Corporate Headquarters

 

167 Technology Drive 
Irvine, CA 92618, USA 
Phone:  949-453-3990 
Fax:     949-450-7249 

Technical Support

 

Online:Email/Chat: Sales Offices

 

For a current list of our domestic and international sales offices go to the Lantronix 
web site at
Disclaimer  

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the 
interference by one of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and (2) 
this device must accept any interference received, including interference that may 
cause undesired operation. 

This device is intended only for OEM Integrators. The OEM integrator should be 
aware of the following important issues. 

Labeling of the End Product 

The label on the end product incorporating the MatchPort b/g module must clearly 
state that it contains an FCC-approved RF module. For example, “This product 
contains an RF transmitter ID#  (put FCC or IC module grant number here).” The 
actual grant number is on the MatchPort b/g label. 

Summary of Contents for MatchPort b/g






























Reviews: