manualshive.com logo in svg

Lantronix EDS-MD Series, Command Reference Manual


Share
Download
background image

5:  Commands and Levels 

EDS-MD® Wired IoT Device Gateway Command Reference 

620 

 

exit 

Exits to the next higher level. 

mode sequential 

Sets sequential mode; will stop after first connection 
that goes through. 

mode simultaneous 

Sets simultaneous mode; will make all possible 
connections. 

no reminder interval 

Clears the HTTP Post reminder interval. HTTP Post 
is sent once only. 

reminder interval 

<minutes>

 

Sets the HTTP Post reminder interval. 

show 

Shows the current configuration. 

show history 

Displays the last 20 commands entered during the 
current CLI session. 

write 

Stores the current configuration in permanent 
memory. 

http post (config-action-http_post:eth0 link state change) level commands 

clrscrn 

Clears the screen. 

connection 

<instance>

 

Enters the next lower level. Specify the instance for 
the next lower level. 

default mode 

Sets default of simultaneous connection mode. 

exit 

Exits to the next higher level. 

mode sequential 

Sets sequential mode; will stop after first connection 
that goes through. 

mode simultaneous 

Sets simultaneous mode; will make all possible 
connections. 

no reminder interval 

Clears the HTTP Post reminder interval. HTTP Post 
is sent once only. 

reminder interval 

<minutes>

 

Sets the HTTP Post reminder interval. 

show 

Shows the current configuration. 

show history 

Displays the last 20 commands entered during the 
current CLI session. 

write 

Stores the current configuration in permanent 
memory. 

icmp (config-icmp) level commands 

clrscrn 

Clears the screen. 

exit 

Exits to the configuration level. 

show 

Displays the current configuration. 

show history 

Displays the last 20 commands entered during the 
current CLI session. 

state disable 

Prevents ICMP packets from being sent or received. 

state enable 

Allows ICMP packets to be sent and received. 

write 

Stores the current configuration in permanent 
memory. 

if 1 (config-if:eth0) level commands 

bootp disable 

Disables BOOTP. 

bootp enable 

Enables BOOTP. 

clrscrn 

Clears the screen. 

default gateway 

<IP address>

 

Sets the configurable gateway IP address to the 
default value. 

Summary of Contents for EDS-MD Series



































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EDS-MD Series

Multitech MultiVOIP MVP210-SS Configuration Manual preview
MultiVOIP MVP210-SS
Brand: Multitech Pages: 36
daviteq STHC-ISG02DB-WS433-CL-04 User Manual preview
STHC-ISG02DB-WS433-CL-04
Brand: daviteq Pages: 25
NetComm NL20 Quick Start Manual preview
NL20
Brand: NetComm Pages: 20
Memotec NetPerformer SDM-9220 Series Hardware Installation Manual preview
NetPerformer SDM-9220 Series
Brand: Memotec Pages: 146
ZyXEL Communications P-661HW-D Series Support Note preview
P-661HW-D Series
Brand: ZyXEL Communications Pages: 146
Crest Audio NDP-ENG ETHERNET NEXSYS GATEWAY Specifications preview
NDP-ENG ETHERNET NEXSYS GATEWAY
Brand: Crest Audio Pages: 2
Samson 5007-2 Series Mounting And Operating Instructions preview
5007-2 Series
Brand: Samson Pages: 72
Technicolor - Thomson SpeedTouch 510 Quick Installation Manual preview
SpeedTouch 510
Brand: Technicolor - Thomson Pages: 21
SAE J2716 User Manual preview
J2716
Brand: SAE Pages: 17
2Wire Intelligent Gateway 1800 User Manual preview
Intelligent Gateway 1800
Brand: 2Wire Pages: 148
Elexim GSM Gateway Proline Digital User Manual preview
GSM Gateway Proline Digital
Brand: Elexim Pages: 11
Galaxy IPTV-DMG User & Installation Manual preview
IPTV-DMG
Brand: Galaxy Pages: 18
Planet Networking & Communication HAC-1000 User Manual preview
HAC-1000
Brand: Planet Networking & Communication Pages: 38
Planet Networking & Communication VGW 20FS Series User Manual preview
VGW 20FS Series
Brand: Planet Networking & Communication Pages: 84
R9 Technology G200 Installation Manual preview
G200
Brand: R9 Technology Pages: 5
2Wire HomePortal 2701HGV Installation Manual preview
HomePortal 2701HGV
Brand: 2Wire Pages: 21
ZyXEL Communications VSG1435 Datasheet preview
VSG1435
Brand: ZyXEL Communications Pages: 2
ZyXEL Communications VSG1432 Specifications preview
VSG1432
Brand: ZyXEL Communications Pages: 2

Brands by name

Popular brands

Load more brands