background image

13

Driver  Installation

Appendix A

Network Application Platforms

On Linux

Follow  these  instructions  when  installing  the  Intel® 

LAN controller base driver for the in Red Hat® and Linux 

operating system.

  Insert  the  motherboard/system  support  CD  to  the 

1. 

optical drive and mount the optional drive in the Linux 

platform.   
Copy  the  base  driver  tar  file  from  the  motherboard/

2. 

system support CD to the directory of your local hard 

disk.  The Intel® LAN driver for Linux OS is located in the 

following directory:

\Driver\LAN_Driver\PRO1000\LINUX. The name format 

of  driver  file  is “e1000-<Version>.tar.gz”.  For  example: 

the file name of driver version 7.0.38 is “e1000-7.0.38. 

tar.gz”.

Untar/unzip the archive, where <x.x.x> is the version 

3. 

number for the driver tar file:

          tar zxf e1000-<x.x.x>.tar.gz 

Change  to  the  driver  src  directory  on  your  system, 

4. 

where <x.x.x> is the version number for the driver tar:

          cd e1000-<x.x.x>/src/ 

Compile  the  driver  module  by  typing  the  following 

5. 

command:

          make install 

The binary will be installed as:

6. 

        /lib/modules/<kernel_version>/kernel/drivers/net/

e1000.o
           The  install  locations  listed  above  are  the  default 

locations. They might not be correct for certain Linux 

distributions.

Load the module using either the insmod or modprobe 

7. 

command:

     

modprobe igb

     

insmod igb

 

Note  that  for  2.6  kernels  the  insmod  command 

can be used if the full path to the driver module is specified. 

For example:
          insmod  /lib/modules/<KERNEL  VERSION>/kernel/

drivers/net/igb/igb.ko
 

With 2.6 based kernels also make sure that older 

igb drivers are removed from the kernel, before loading 

the new module:
 

    rmmod igb; modprobe igb

Assign an IP address to the interface by entering the 

8. 

following, where <x> is the interface number:

          ifconfig eth<x> <IP_address> 

Verify  that  the  interface  works.  Enter  the  following, 

9. 

where  <IP_address>  is  the  IP  address  for  another 

machine on the same subnet as the interface that is 

being tested:

          ping <IP_address>

Note:  The system uses Intel 82574L Ethernet 

controllers, you could obtain the latest drivers at 

the Intel download center:

http://www.intel.com/products/ethernet/

Summary of Contents for FW-7581
























Reviews: