23
it can be replaced.
6. If you do not use your mobile phone for an extended period,
remember to recharge the battery to optimize its use time.
7. Do not throw batteries away with household waste: recycle
them in accordance with the manufacturer’s guidelines. If the
battery is damaged, contact the after-sales service or the nearest
authorized LANIX dealer.
8. Unplug the charger from the wall socket when the battery is
fully charged in order to reduce your energy consumption.
9. Do not leave the battery being charged for more than a week
as this might result in an overload and reduce the life of the
product.
10. Handle the SIM cards with care: wipe them with a soft cloth
if they appear dirty.
11. Emergency calls: the emergency numbers may not be
accessible on all mobile telephone networks, in isolated areas or
areas where there is no coverage; check first with your operator.
12. Radio Frequency Exposure: Your mobile phone has been
designed and manufactured in accordance with the international
guidelines (ICNIRP1) on exposure to radio frequencies. These
guidelines, which are based on various studies and research,
have been developed by independent scientific organizations to
ensure the safety of everyone who uses a mobile phone.
~ General Notice
Due to the used enclosure material, the GSM mobile phone shall
only be connected to a USB Interface of version 2.0 or higher.
The connection to so called power USB is prohibited.
The adapter shall be installed near the equipment and shall be
easily accessible.
Do not use the mobile phone in the environment at too high or
too low temperature, never expose the mobile phone under
strong sunshine or too wet environment. The suitable
temperature for the phone is -10
℃
to +45
℃
.
The maximum operating ambient temperature of the charger
declared by the manufacturer is 40
℃
.
Caution risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to the instructions.
FCC Regulations
This mobile phone complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
This mobile phone has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
24
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
FCC Note:
Caution: Changes or modifications not expressly approved by
the party responsible for compliance could void the user‘s
authority to operate the equipment.
RF Exposure Information (SAR)
This phone is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set
by the Federal Communications Commission of the United
States.
During SAR testing, this device was set to transmit at its highest
certified power level in all tested frequency bands, and placed in
positions that simulate RF exposure in usage against the head
with no separation, and near the body with the separation of 10
mm. Although the SAR is determined at the highest certified
power level, the actual SAR level of the device while operating
can be well below the maximum value. This is because the
phone is designed to operate at multiple power levels so as to use
only the power required to reach the network. In general, the
closer you are to a wireless base station antenna, the lower the
power output.
The exposure standard for wireless devices employing a unit of
measurement is known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6W/kg.
This device is complied with SAR for general population
/uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had
been tested in accordance with the measurement methods and
procedures specified in IEEE1528. This device has been tested
and meets the FCC RF exposure guidelines when tested with the
device directly contacted to the body.
