background image

 

5

 

IMPORTANT READ 

FIRST IMPORTANT

 

WARNING:

 

KEEP WATER AND SOLUTIONS OUT OF CONTROLS.  
NEVER SPRAY OR HOSE CONTROL CONSOLE, 
ELECTRICAL CONNECTIONS, ETC. 

CAUTION:

 

MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, 
MUCOUS MEMBRANES AND CLOTHING.  
PRECAUTIONS SHOULD BE TAKEN TO WEAR RUBBER 
GLOVES, GOGGLES OR FACE SHIELD AND 
PROTECTIVE CLOTHING.  CAREFULLY READ THE 
WARNING AND FOLLOW THE DIRECTIONS ON THE 
LABEL OF THE CLEANER TO BE USED. 

NOTICE:

 

Service on this, or any other, LANG appliance must be 
performed by qualified personnel only.  Consult your 
LANG authorized service agent directory or call the 
factory at 1-800-807-9054, or 

WWW.STAR-MFG.COM

   for 

the service agent nearest you. 

WARNING:

 

BOTH HIGH AND LOW VOLTAGES ARE PRESENT 
INSIDE THIS APPLIANCE WHEN THE UNIT IS 
PLUGGED/WIRED INTO A LIVE RECEPTACLE.  BEFORE 
REPLACING ANY PARTS, DISCONNECT THE UNIT 
FROM THE ELECTRIC POWER SUPPLY. 

CAUTION:

 

USE OF ANY REPLACEMENT PARTS OTHER THAN 
THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED 
DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE 
OPERATOR AND DAMAGE TO THE EQUIPMENT AND 
WILL VOID ALL WARRANTIES.

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for CL36GF
















Reviews: