background image

 

12

 

 Installation 

cont’d 

Gas Conversions 

1.  Disconnect the griddle from power and close main gas supply valve. 
2.  Remove the front panels (remove the two hex screws on the bottom front of the body for each 

panel.  Then lift the panels up and off from the keyhole slots). 

3.  Disconnect the 3/8” flex tubing from the 90

°

 orifice fittings.  

4.  Remove the 90

°

 orifice fittings from the griddle. 

5.  Replace the orifice spud on each of the 90

°

 orifice fittings (making sure to apply pipe thread 

compound) with the new orifice spud. 

6.  Re-install the 90

°

 orifice fittings into the griddle.  Do not over tighten the fittings retaining nut. 

7.  Re-connect the 3/8” flex tubing to each of the 90

°

 orifice fittings. 

8.  Remove the cap from the regulator adjustment screw. 
9.  Remove the regulator adjustment screw and spring from the regulator body. 
10. Insert the new spring from the conversion kit and install the adjustment screw over it. 
11. Place the regulator pressure range sticker over the existing pressure range sticker. 
12. Place caution sticker from the conversion kit adjacent to the data label. 
13. Re-connect the griddle to power. 
14. Open the main gas valve and check for leaks using a soap solution. 
15.  Adjust gas pressure (Natural gas=5”W/C and Propane=10”W/C). 
16. Install regulator adjustment screw cap. 

17. 

Install front panels.

 

Natural Gas to Propane 

 

Part No. 

Description 

Qty. 

2A-80400-12

 

Burner orifice, drilled #53 

1 per 12” 

2V-80505-11

 

Combination gas valve spring, includes: 

1. Spring 
2. Seal screw 
3. Caution sticker 

 

 

Propane to Natural Gas 

Part No. 

Description 

Qty. 

2A-80400-11

 

Burner Orifice, Drilled #43 

1 per 12” 

2V-80505-16

 

Combination Gas Valve Spring, Includes: 

1. Spring 
2. Seal Screw 
3. Caution Sticker 

 

 

NOTICE 

Kits designed to accommodate griddles from sea level to 5000 feet.  
Contact factory for orifice sizes on installations above 5000 feet. 

 

 

Summary of Contents for 236ZC Chrome





























Reviews: