background image

 

19

 

TROUBLESHOOTING CONT’D 

9.2  TESTS 

NOTICE:

 

Service on this, or any other, LANG appliance must be 
performed by qualified personnel only.  Consult your 
LANG authorized service agent directory or call the 
factory at 1-800-807-9054, or WWW.STAR-MFG.COM   
For the service agent nearest you. 

WARNING:

 

BOTH HIGH AND LOW VOLTAGES ARE PRESENT 
INSIDE THIS APPLIANCE WHEN THE UNIT IS 
PLUGGED/WIRED INTO A LIVE RECEPTACLE.  
BEFORE REPLACING ANY PARTS, DISCONNECT THE 
UNIT FROM THE ELECTRIC POWER SUPPLY. 

 

 

 

POSSIBLE CAUSE

 

TEST

 

Failed regulator 

 

Replace regulator 

Failed thermostat 

 

Check for correct temperature, replace thermostat 

Failed transformer 

 

Check transformer for correct voltage, replace as necessary 

Failed igniter 

 

Replace as necessary 

Failed spark module 

 

Check for correct incoming voltage at module 

Failed power cord or plug 

 

Check cord and plug for proper voltage 

Failed power switch 

 

Check switch for continuity across poles 

Failed pilot light 

 

Check for continuity across pilot light leads 

Failed gas valve 

 

Remove the wires from the valve terminals and check for 
continuity across the coil 

Incorrect gas pressure 

 

Adjust to correct pressure 

Plugged regulator vent, or orifice 

 

Clean as necessary 

 

CAUTION:

   

  USE OF ANY REPLACEMENT PARTS OTHER THAN 

THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED 
DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE 
OPERATOR AND DAMAGE TO THE EQUIPMENT AND 
WILL VOID ALL WARRANTIES.

 

 

 

 

Summary of Contents for 224TH





























Reviews: