SAVE THESE INSTRUCTIONS
7). Caution:
These professional loudspeaker systems are capable of generating very high sound pressure levels. Use care with placement
and operation to avoid excessive levels that can cause permament hearing damage.
8). Exposure
to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise
induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S.
Government's Occupational Safety and Health Administration (OSHA) has specified the permissible noise level exposure in the chart
oposite.
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors in
the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if
exposure exceeds the limits set forth above. To ensure against potentially dangerous exposure to high sound pressure levels it is
recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be
protected by hearing protectors while this unit is in operation.
9). Servicing:
The user should not attempt to service these products. Refer all servicing to qualified service personnel
Page3 /4
N
X
41
0
4
1
0
SPECIFICATIONS
Impedance:
8 Ohms
Loudspeakers:
10" Neodymium Drivers (8 Ohm)
Power Rating:
800W RMS
Size: W*D*H:
640*400*695
Weight:
27.5 Kg
TM
Dual Speakon Jack combi sockets
TM
(Use either: 1/4 Mono Jack or NL4 Speakon Connector-wired 1+1-)
Switchable Compression Driver
Metal detachable grille
Duration Per Day
In Hours
8
6
4
3
2
1 ½
1
½
¼ or less
Sound Level dBA,
slow response
90
92
95
97
100
102
105
110
115
IMPORTANT SAFETY INSTRUCTIONS
1). Read Instructions
carefully before installing or operating this product.
2). Retain these Instructions.
3). Comply with Warnings:
All warnings and instructions for these products should be adhered to.
4). Unpacking:
On unpacking your product please check carefully for any signs of damage that may have occured whilst in transit from the Laney factory to your dealer. In the unlikely
event that there has been damage, please repack your unit in it original carton and consult your dealer. we strongly advise you to keep your original transit carton, since in the unlikly
event that your unit should develop a fault, you will be able to return it to you dealer for rectification securely packed.
5). Amplifier Connection:
In order to avoid damage , it is advisable to establish and follow a pattern for turning on and off your system. With all system parts connected, turn on
source equipment, tape decks, cd players, mixers, effects processors etc, BEFORE turing on your guitar amplifier. Many products have lare transient surges at turn on anf off which can
cause damage to your speakers.
By turning on your guitar amplifier LAST and making sure it level control is set to a minimum, any transients from other equipment should not reach your loud speakers. Wait till all
system parts have stabillised, usually a couple of seconds. Similarly when turning off your system always turn down the level controls on your guitar amplifier and then turn off its power
before turning off other equipment
6). Cables:
Never use shielded or microphone cable for any speaker connections as this will not be stubstantial enough to handle the amplifier load and could cause damage to your
complete system.
This product conforms to the requirements of the following European Regulations, Directives & Rules:-
CE Mark (93/68/EEC), Low Voltage (72/23/EEC), EMC (93/68/EEC),
RoHS (EU2002/95/EC), WEEE (EU2002/96/EC)
In order to reduce environmental damage, at the end of its useful life, this product must not
be disposed of along with normal household waste to landfill sites. It must be taken to an
approved recycling centre according to the recommendations of the WEEE
(Waste Electrical and Electronic Equipment) directive applicable in your country.
TM
Trademarks: Speakon is a trademark and/or service mark of Neutrik®AG.
Page3 /4
Duration Per Day
In Hours
8
6
4
3
2
1 ½
1
½
¼ or less
Sound Level dBA,
slow response
90
92
95
97
100
102
105
110
115
IMPORTANT SAFETY INSTRUCTIONS
1). Read Instructions
carefully before installing or operating this product.
2). Retain these Instructions.
3). Comply with Warnings:
All warnings and instructions for these products should be adhered
to.
4). Unpacking:
On unpacking your product please check carefully for any signs of damage that may
have occured whilst in transit from the Laney factory to your dealer. In the unlikely event that there
has been damage, please repack your unit in it original carton and consult your dealer. We strongly
advise you to keep your original transit carton, since in the unlikly event that your unit should
develop a fault, you will be able to return it to you dealer for rectification securely packed.
5). Amplifier Connection:
In order to avoid damage , it is advisable to establish and follow a
pattern for turning on and off your system. With all system parts connected, turn on source
equipment, tape decks, cd players, mixers, effects processors etc, BEFORE turing on your guitar
amplifier. Many products have large transient surges at turn on and off which can cause damage to
your speakers.
By turning on your guitar amplifier LAST and making sure its level control is set to a minimum, any
transients from other equipment should not reach your loud speakers. Wait till all system parts have
stabillised, usually a couple of seconds. Similarly when turning off your system always turn down the
level controls on your guitar amplifier and then turn off its power before turning off other
equipment
6). Cables:
Never use shielded or microphone cable for any speaker connections as this will not be
stubstantial enough to handle the amplifier load and could cause damage to your complete system.
7). Caution:
These professional loudspeaker systems are capable of generating very high sound
pressure levels. Use care with placement and operation to avoid excessive levels that can cause
permament hearing damage.
8). Exposure
to extremely high noise levels may cause a permanent hearing loss. Individuals vary
considerably in susceptibility to noise induced hearing loss, but nearly everyone will lose some
hearing if exposed to sufficiently intense noise
for a sufficient time. The U.S. Government's
Occupational Safety and Health Administration
(OSHA) has specified the permissible noise
level exposure in the chart oposite.
According to OSHA, any exposure in excess of
the above permissible limits could result in
some hearing loss. Ear plugs or protectors in
the ear canals or over the ears must be worn
when operating this amplification system in
order to prevent a permanent hearing loss if
exposure exceeds the limits set forth oposite.
To ensure against potentially dangerous
exposure to high sound pressure levels it is recommended that all persons exposed to equipment
capable of producing high sound pressure levels such as this amplification system be protected by
hearing protectors while this unit is in operation.
9). Servicing:
The user should not attempt to service these products. Refer all servicing to
qualified service personnel
SAVE THESE INSTRUCTIONS
Conection 1
Connect to "INPUT" makes the cabinet active.
Conection 2
Connect to "LINK" to plug in another cabinet, (such as the Laney
NX115).
Horn Controls
The HF Compression Driver can be turned ON or OFF.
Or in the ON position, used at Full or Half Power
NX410
HORN
ON
OFF
FULL
HALF
INPUT
LINK
8 OHMS
800 WATTS RMS
DESIGNED AND BUILT
IN THE UK BY LANEY
SERIAL NUMBER
POWER RATING:
O
B
M
O
C -
K
C
A
J
"
4
/
1
O
B
M
O
C -
K
C
A
J
"
4
/
1
S
P
E
A
K
O
N
O
B
M
O
C -
K
C
A
J
"
4
/
1
O
B
M
O
C -
K
C
A
J
"
4
/
1
S
P
E
A
K
O
N