Laney
L
1
0
X
2
R
TW
IN
6
6
Laney
L
1
0
X
2
R
TW
IN
7
7
E
XTENSION
L
OUDSPEAKER
8
OHM
M
INIMUM
I
MPEDANCE
R
EFER
TO
U
SER
M
ANUAL
F
OR
L
OUDSPEAKER
C
ONNECTIONS
www.laney.co.uk
Laney
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
P
OWER
A
MP
I
N
P
RE
A
MP
O
UT
LX120RTWIN FRONT / REAR PANEL FEATURES
1
2
3
21
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
then be in complete control of the slave power amplifier.
Loudspeakers:
Connect your louspeakers here. The impedance of the cabinet/s
should not be less than 4 Ohms. Connecting cabinets that have a lower inpedance
than 4 Ohms will result in the amplifier overheating. Continual use in this manner may
cause perminent damage.
Power Inlet Socket:
Connect your power source here.
Make sure that the
specified voltage is correct for your country!
Also here in the drawer is the
main safety fuse for the unit.
Only use the correct size and rating of fuse as
specified on the panel.
Main Power Switch:
for the unit. (Always switch off and
disconnect the power cord when not in use)
Main Power LED:
When illuminated indicates that power is
connected to the unit and it is ready to go.
FX Send / Return:
Line level FX Loop to connect to an external
effects controller.
Footswitch:
Connect a Laney FS2 footswitch here to enable
remote switching for the channel and reverb/FX. Note: Drive
channel must be enabled (via ) for channel switching with a
footswitch to function.
13
21
20
CD/L
INE
I
N
F
OOTSWITCH
LX120RT
WIN
R
EVERB
FX S
END
FX R
ETURN
T
REBLE
M
ID
B
ASS
M
ASTER
C
RUNCH
T
REBLE
M
ID
B
ASS
V
OLUME
XTS
D
RIVE
E
QUALISATION
D
RIVE
C
LEAN
P
OWER
1
0
O
N
I
NPUT
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
11
13
Crunch ON/OFF:
Switch in to activate the overdrive ‘Crunch’ channel. When active, control the amount of distortion with and the
overall volume with
Treble:
Controls the amount of treble present on the clean channel.
Mid:
Controls the amount of mid present on the clean channel.
Bass:
Controls the amount of bass or bottom end present on the clean channel.
Volume:
Controls the volume level of the clean channel.
Input:
This socket should be used for connecting your instrument to the amplifier. Only use a good quality screened cable.
Power Amp In Preamp Out:
These jacks are primarily used to connect other power amplifiers or to connect LX120RH amplifiers
together to boost power outputs. When connecting to another power amplifier the preamplifier output jack should be used. The signal at
this socket will be affected by all the controls on the preamplifier. When connecting two LX120RH amplifiers together to boost power
levels the master amplifier preamplifier out jack should be connected to the power amplifier input socket of the slave. The master will
12
11
CD/Line In:
Fancy playing along with a backing track? Connect your CD/MP3 player here.
Reverb:
Controls the amount of reverb applied to the signal
Treble:
Controls the amount of treble present on the drive channel.
Mid:
Controls the amount of mid present on the drive channel.
Bass:
Controls the amount of bass or bottom end present on the drive channel.
XTS:
e
X
treme
T
one
S
haping. This applies a scooped mid tone shape to the drive channel and boosts certain key frequencies for a
unique sound.
Master:
Controls the overall level on the drive channel. Use with
Crunch:
Controls the crunch channel gain, low down for classic rock and blues, higher up for hard rock and metal.... the higher you
go the more Extreme it gets. Use in conjunction with to get the overall level balanced how you want it. LED Indicates that the
drive channel is active.
12
11
