manualshive.com logo in svg

Lanex EtherCon TM-170.1, Operating Manual

Share
Download
Lanex EtherCon TM-170.1 Operating Manual Download Page 28

10Base-T/100Base-TX/E3 Converter 

Operating Manual 

IOA170-1A                                                  22 

                                            January 2006 

 

• 

DHCP – server

 frames filtering; OFFER and ACKNOWLEDGE packet filtering 

 

6.4.2.2 Tab – Ethernet – Monitoring  

 

Fig. 6-10. Interfaces– Ethernet, Monitoring. 

 
The tab enables viewing the Ethernet interface signal, the following parameters are 

monitored 

 

LINK1

 – activity of port 1 

LINK2

 – activity of port 2  

 

LANPacketRXCnt

 – 

number of packets received from Ethernet interface 

LANErrPacketRXCnt

 –

number of errored packets received from Ethernet interface 

LANFCtrlPacketRXCnt

 –

 number of packets with flow control received from Ethernet interface 

LANFCtrlPacketTXCnt

 – 

number of packets with flow control sent from Ethernet interface 

WANPacketRXCnt

 – 

number of packets received from E3 

WANErrPacketRXCnt

 – 

number of errored packets received from E3 

WANFCtrlPacketRXCnt

 - 

number of packets with flow control received from ES interface

 

WANFCtrlPacketTXCnt

 - 

number of packets with flow control sent from to ES interface 

 

 
 
 
 
 
 

Summary of Contents for EtherCon TM-170.1





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands