ASSEMBLE
WITH
CARE!
Pangard II
Polyester
Powdercoat is
a
strong,
long
‐
lasting
finish.
To
protect
this
finish
during
assembly,
place
unwrapped
powdercoated parts
on
packaging
foam
or
other
non
‐
marring
surface.
Do
not
place
or
slide
powdercoated parts
on
concrete
or
other
hard
or
textured
surface
– this
will
damage
the
finish
causing
rust
to
occur.
Use
touch
‐
up
paint
on
any
gouges
in
the
finish
caused
by
assembly
tools.
PROCEDURE
FOR
INSTALLATION:
1.
Prepare
proper
concrete
slab
as
required.
2.
Freestanding
unit
ships
with
glides
installed.
Unit
can
be
set
in
place.
Note:
DO
NOT
DRAG
unit
across
concrete
or
other
rough
surfaces.
This
could
damage
the
finish.
For
SURFACE
MOUNT:
leave
glides
installed.
1.
Turn
unit
upside
down
on
protective
padding.
Install
surface
mount
bolts
as
shown
in
Fig.
4.
2.
Set
unit
in
position.
Trace
around
anchors
to
mark
hole
locations.
3.
Move
unit.
Drill
holes
according
to
anchor
manufacturer’s
recommendations.
Clear
holes
of
debris.
4.
Test
fit
unit
to
make
sure
holes
align
with
anchor
bolts.
5.
Install
drop
‐
in
anchors
(or
other
anchoring
option).
6.
Remove
surface
mount
bolts
from
unit.
Install
into
drop
‐
in
anchors.
Use
the
supplied
washer
as
a
height
gauge,
see
Fig.
1,
for
the
surface
mount
bolt.
The
top
of
the
threaded
portion
of
the
surface
mount
bolt
should
be
flush
with
the
top
of
the
washer.
Remove
the
washer
after
setting
the
height,
and
reuse
for
the
second
surface
mount
bolt.
7.
Set
unit
over
surface
mount
anchors.
Verify
that
the
rubber
pads
(glides)
are
sitting
firmly
on
the
hard
surface.
Do
not
allow
the
weight
of
the
bench
to
sit
on
top
of
the
surface
mount
bolt
as
this
will
cause
damage.
8.
Install
set
screws
to
secure,
see
Fig.
2.
Gently
lift
up
on
the
ends
of
the
bench
to
verify
proper
mounting.
For
EMBEDDED
MOUNT:
leave
glides
installed.
1.
Turn
unit
upside
down
on
protective
padding.
2.
Remove
one
screw
from
each
glide
pad
as
shown
in
Fig.
5.
3.
Install
threaded
rods
as
shown
in
Fig.
6.
4.
Set
unit
in
position.
Trace
around
rods
to
mark
hole
locations.
5.
Move
unit.
Drill
holes
according
to
anchor
manufacturer’s
recommendations,
see
Fig.
3.
Clear
holes
of
debris.
6.
Test
fit
unit
to
make
sure
holes
align
and
embedded
rods
are
not
resting
on
the
bottom
of
the
holes.
7.
Remove
unit
and
fill
holes
with
anchoring
adhesive
as
recommended
by
manufacturer.
Fill
holes
from
the
bottom
up
to
prevent
air
pockets.
Do
not
fill
holes
to
the
top.
8.
Set
unit
in
place.
Wipe
away
excess
adhesive
before
it
cures.
9.
Allow
bench
to
sit
undisturbed
until
adhesive
fully
cures.
Included
components:
Tools
Required
for
surface
mount
or
embedded
options:
•
Safety
glasses
•
Hammer
drill
with
masonry
bits
•
Hex
key,
1/8”
(surface
mount)
7/32”
(embedded)
•
Flat
blade
screwdriver
(surface
mount)
•
Chemical
anchoring
adhesive
(Hilti
HIT
RE
500
or
equivalent)
(embedded)
•
(2)
Zinc
‐
plated
drop
‐
in
anchors
for
5/8
‐
11
thread
size
(surface
mount),
for
use
with
Magni
‐
coated
bolts
Installation Guide
Rest
bench
www.landscapeforms.com Ph: 800.521.2546
Date: November 6, 2017
Page 1 of 2
5/8
‐
11
threaded
Bolt
2x
‐
surface
mount
1/4
‐
20
x
1
‐
1/2”
hex
Set
screw
2x
– surface
mount
3/8
‐
16
x
5
‐
1/8”
Threaded
rod
4x
– embed
mount
Backed
bench
Backless
bench
5/8
washer
for
spacing
1x
– surface
mount
