manualshive.com logo in svg

Landoll Brillion Turfmaker II, Operator'S Manual

Share
Download
Landoll Brillion Turfmaker II Operator'S Manual Download Page 97

MAINTENANCE

9K998-0522                                                                                                                                                                         

5-9

Figure 5-10:  Front Box Seed Shaft Coupler

3.

Rear Seed Box:

  Seed Box Feed Roll Coupling 

which joins the left and right Seed Shafts changes 
Seed Meters on the left Seed Box in comparison with 
Seed Meters on the right Seed Box. To adjust Feed 
Roll Coupling, loosen Jam Nuts and Set Screws on 
Coupling RH Seed Shaft is treaded into Coupling. 
Turn RH Seed Shaft threading it in or out as needed 
to equalize Seed Meters. Re-tighten Set Screws 
against flat side on Seed Shaft, re-tighten Jam Nuts. 

See Figure 5-13.

Figure 5-11:  Rear Box Seed Shaft Couple

4.

Front Seed Box:  

Individual Seed Meter Cups can 

be adjusted as required. Adjustments can be made 
by loosening the 1/4-20 x 5/8 Machine Screws that 
mount the Seed Meter Cup to the Seed Box and the 
1/4-20 Nut that attaches the Seed Meter Support to 
the Seed Meter Cups. 

See Figure 5-9.

 Adjust the 

affected Seed Meter Cup so the Feed Shutoff is 
against the Seed Meter Cup Star Washer in the Seed 
Meter Cup (closed). Be sure the Feed Roll stays 
engaged in the Seed Meter Cup Star Washer. 

See 

Figure 5-12. 

Check for binding by turning Seed 

Shaft. After adjustments have been made seal the 
Seed Meter Cups to Seed Box with clear Silicone.

Figure 5-12:  Large Seed Meter

5.

Rear Seed Box:  

Individual Seed Meter Cups can be 

adjusted as required. Adjustments can be made by 
loosening the 1/4-20 x 5/8 Machine Screws that 
mount the Seed Meter Cup to the Seed Box. Adjust 
the affected Seed Meter Cup so the Feed Shutoff is 
against the Seed Meter Cup Star Washer in the Seed 
Meter Cup (closed). Be sure the Feed Roll stays 
engaged in the Seed Meter Cup Star Washer. 

See 

Figure 5-13.

Figure 5-13:  Small Seed Meter

RH

Seed Shaft

Seed Shaft

Coupling Half

Locknut,

Flange 1/4-20

Bolt,1/4-20

x 1-3/4

Seed Shaft

Coupling Half

 

LH

Seed Shaft

SL2 OpSeedShaftCoupler

Jam Nut

 

Set

Screw

Feed Roll

Coupler

Seed Meter

Cup

Seed Meter

Cup Star Washer

LH Seed

Shaft

RH Seed

Shaft

 

)HHG6KXWRႇ

 

Feed Roll

Washer

 

)HHG6KXWRႇ

Seed Meter

Cup

Seed Meter Cup

Star Washer

Feed Roll

 

Seed Meter Cup

Star Washer

 

Feed Roll

Seed Meter

Cup

Feed

6KXWRႇ

Washer

 

Summary of Contents for Brillion Turfmaker II













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands