2-10
9K713-0522
ASSEMBLY
Warning Lamp Installation,
8FT and 10FT
NOTE
8FT 3-PT Model is shown, 8FT Drawbar, 10FT 3-PT and
10FT Drawbar models similar.
1. Attach longer Light Bracket to the Transmission
housing located on the left side of the Seeder, with
3/8-16 x 1-1/2 Bolts, Lock Washers and Nuts.
2. Attach Amber Lamp to the upper portion of the longer
Light Bracket with 1/4-20 x 1-1/4 Bolts and Locknuts.
3. Attach a Red Lamp below the Amber Lamp with
1/4-20 x 1-1/4 Bolts and Locknuts. Ensure Red Lamp
lenses faces rearward.
4. On the right side of the Seeder attach the shorter
Light Bracket to the Angle Bracket with 1/2-13 x 1-1/4
Bolts, Lock Washers and Nuts.
5. Attach Amber Lamp to the upper portion of the Light
Bracket with 1/4-20 x 1-1/4 Bolts and Locknuts.
6. Attach a Red Lamp below the Amber Lamp with
1/4-20 x 1-1/4 Bolts and Locknuts. Ensure Red Lamp
lenses faces rearward.
7. Attach the Flasher Control Module to the Module
Bracket with 1/4-20 x 1-1/2 Bolts and Locknuts.
IMPORTANT
Cords are marked Yellow Tape for Left and Green
Tape for Right.
8. Lay out the Lamp Harness along the Seeder Frame,
Cords with Yellow Tape Left and Cords with Green
Tape Right. Connect the Harness to the Flasher
Control Module 6-Prong Connector.
9. Route the left and right cords along the front of the
Frame Tube up to the outer Light Brackets. Connect
the 2-Prong Connector to the Amber Lamps and the
3-Prong Connector to the Red Lamps.
10. Lay out the 7-Pin Harness along the 3-PT Hitch or
Drawbar with the 4-Prong Connector towards the
Seeder. 3-PT Hitch, route the 4-Prong Connector
Cord through the Frame Loop to the Module.
Drawbar, route the 7-Pin Harness along the Drawbar,
through the Hose Support up to the Tractor. Connect
7-Pin Harness 4-Prong Connector to the Flasher
Control Module.
11. Bundle and secure excess Cords to the Module
Bracket with Tie Wraps. Along the Seeder Frame,
secure Harness Cords with Tie Wraps to the frame
end plate slots, Slotted Tabs and Hydraulic Hoses.
Bundle and secure 7-Pin Harness to the Drawbar
Hydraulic Hoses or 3-PT Hitch Frame Slots allowing
enough Harness length to reach the Tractor Socket.
NOTE
If equipped with optional Electrical Clutch, install, route
and secure Electric Clutch Harness with the Warning
Lamp Harness.
IMPORTANT
All wires must be firmly attached to Machine Frame
members or Hydraulic Hoses so they do not sag or
become torn loose by field debris.
12. Attach the SMV sign to the SMV Mount located on the
center on the Front Frame with 5/16-18 x 1 Bolts, Flat
Washers, and Locknuts.
13. Attach the Connector Holder to the Drawbar Hose
Holder or 3-PT Hitch with 1/4-20 x 1 Bolts, Flat
Washers, and Locknuts.
NOTE
The 7-Pin Plug on the other end of the 7-Pin Harness
connects to the Tractor Socket when in use. When not in
use, it can be stored in the Connector Holder on the
Drawbar Hose Holder or 3-PT Hitch. Allow enough
harness length to reach Tractor Socket and roll or fold up
excess and secure to Drawbar Hydraulic Hoses or 3-PT
Hitch.
Figure 2-14: Flasher Control Module and Bracket
Module Bracket
Flasher Control Module
Locknut,1/4-20
Bolt,1/4-20 x 1-1/2
Summary of Contents for Brillion Alfalfa SS108
