background image

3-2

F-1105-1120

ASSEMBLY INSTRUCTIONS

Center Frame Assembly- 9630FH

IMPORTANT

Read all safety precautions at the front of the section
before attempting any of the following procedures.

WARNING

1.

Position the two center frame halves side-by-side on

the ground.

2.

Bolt the two center frame halves together using 5/8 x
2 bolts and locknuts

See Figure 3-1

.

3.

Now place the frame assemblies on stands 36” off
the ground.

4.

Remove any shank assemblies or extensions that
have been turned around or mounted inside the
frame for shipping, and reposition,

See Figures 2-2

through

See Figures 2-6

in “STANDARD

SPECIFICATION” section for shank placement.

5.

Install a UHMW bearing between both inner bearing
locators around the center lift assembly.

6.

Insert a UHMW bearing into each bearing cap and
install the cap and bearing over the end of center lift
assembly.

7.

Raise the center lift assembly into the center frame
and attach each end bearing cap to the center frame
with 5/8 x 4 bolts and lock nuts

8.

Install the two inner lift bearing mounts with 5/8 x 2
bolts and lock nuts.

NOTE

Make sure the center lift will rotate freely in the center 
frame after it is assembled.

9.

Attach the bottom end of the cylinder lift arms to the
outside of bearing housing mounts with 1 x 2-3/4
bolts and 1 locknuts.

10.

Connect the top end of the cylinder lift arms to the
radius rod with 1 x 3-1/2 bolts and locknuts. Initially,
set the radius rod to 54” pin centers for the center
frame.

11.

Install the two 4x10 master cylinders to the cylinder
lift arms, and the center lift. Install the cylinders with
the rod end down, and with rephasing cap to the top.
Use a 1” welded head pin, 1” machine busing on
cotter pin on the rod end of the cylinder. Insert the pin
so the head will be facing the tire. Install the transport
locks in the storage locations on back of the lift
cylinder plates with L-pins and hairpin clips.

12.

Connect the rear of the gauge wheel lift tubes to the
center lift with 1-1/4 x 2-3/4 step pin, 1/2 x 2-1/4 roll
pin, and 1 locknut. Insert the pin so the nut is away
from the lift cylinder.

13.

All lifts and hubs/spindle come already assembled
from the factory.

14.

Install the 320/70 R15 tire/wheel assemblies to all
hub/spindle assemblies using 5/8 wheel nuts.

15.

Install the 8 port manifold to 2 hole plate toward front
of center frame assembly with 1/2 x 3-1/2 bolts and
1/2 lock nuts

See Figure 3-1

.

16.

Install the lift/fold manifold assembly on 2 hole plate
on rear of center frame tube using 1/2 x 3-1/2 bolt
and 1/2 lock nut

See Figure 3-1

.

Do not attempt to lift heavy parts (such as the
frame and rock shaft) manually. Use a hoist or a
fork lift to move these parts into position.

Summary of Contents for 9630FH













































































































Reviews: