13
Operations
Shut Down And Clean Up
STEP 1:
Remove detergent suction
tube from container and insert into
one gallon of fresh water. Open
detergent valve, pull trigger on
spray gun and siphon water for one
minute.
STEP 4:
Turn off water supply.
STEP 2:
Turn burner switch off and
continue spraying, allowing the
water to cool to below 100°.
STEP 5:
Squeeze trigger on spray
gun to relieve remaining pressure.
STEP 3:
Turn engine key switch
off.
Landa SLT/SLX Diesel Dealer’s Manual 9.807-539.0 - AE
9.80
1-427.
0
OFF
GL
ST
DO NO
T OVER
LOAD G
ENER
ATO
R
Uni
ts
eq
uipp
ed
w
ith opt
ion
al
gen
erator
sh
ou
ld
not e
xceed
100
0 w
atts
resistive
load.
See
Se
rvice Man
ua
l fo
r details
.
CA
UTION
ON
TA
CH
/HO
UR
FO
R
OUT
DOO
R
US
E O
NL
Y —
ST
ORE
IN
DOO
RS
Ass
em
bl
ed
in
USA
Us
e Ap
pr
oved
De
te
rg
en
t On
ly.
Co
nt
ain
s c
om
po
nents
fr
om
one
or m
ore
of
the
fo
llow
ing
coun
tri
es
:
Uni
te
d Sta
tes
, C
hi
na
, I
ta
ly,
J
apa
n an
d Thai
la
nd
.
8.9
32-
96
8.0
Burner
Switch
9.801-42
7.0
OF
F
GL
ST
DO N
OT OV
ERLOA
D GENE
RAT
OR
Uni
ts e
quip
ped
with
opt
ional generator
sh
ould no
t ex
cee
d 10
00
watts
re
sis
tive
loa
d.
See
Se
rvice
M
an
ual
for
de
tail
s.
CA
UTION
ON
TA
CH
/HOU
R
Engine
Key
Switch
Storage
CAUTION: Always store your pressure washer in a
location where the temperature will not fall below
32°F (0°C). The pump in this machine is susceptible
to permanent damage if frozen. FREEZE DAMAGE
IS NOT COVERED BY WARRANTY.
1.
Stop the pressure washer, squeeze spray gun
trigger to release pressure.
2.
Detach water supply hose and high pressure hose.
3.
Turn on the machine for a few seconds, until
remaining water exits. Turn engine off immediately.
4.
Drain the fuel and oil from the engine.
5.
Do not allow high pressure hose to become kinked.
6.
Store the machine and accessories in a room
which does not reach freezing temperatures.
CAUTION: Failure to follow the above directions
will result in damage to your pressure washer.
When the pressure washer is not being operated or is
being stored for more than one month, follow these
instructions:
1.
Replenish engine oil to upper level.
2.
Drain diesel from fuel tank, fuel line, fuel valve and
carburetor.
3.
Pour about one teaspoon of engine oil through the
spark plug hole, pull the starter grip several times
and replace the plug. Then pull the starter grip
slowly until you feel increased pressure which
indicates the piston is on its compression stroke
and leave it in that position. This closes both the
intake and exhaust valves to prevent rusting of
cylinder.
4.
Cover the pressure washer and store in a clean,
dry place that is well ventilated away from open
flame or sparks.
NOTE:
The use of a fuel additive,
such as STA-BIL
®
, or an equivalent, will minimize
the formulation of fuel deposits during shortage.
Such additives may be added to the gasoline in the
fuel tank of the engine, or to the gasoline in a
storage container.
After Extended Storage
CAUTION: Prior to restarting, thaw out
any possible ice from pressure washer
hoses, spray gun or wand.
Engine Maintenance
During the winter months, rare atmospheric conditions
may develop which will cause an icing condition in the
carburetor. If this develops, the engine may run rough,
lose power and may stall. This temporary condition can
be overcome by deflecting some of the hot air from the
engine over the carburetor area.
NOTE:
Refer to the
engine manufacturer's manual for service and mainte-
nance of the engine.
