Landa Platinum Series Operator'S Manual Download Page 5

PHW/PHWS SERIES PRESSURE WASHER

 

OPERATOR’S MANUAL

5

WARNING: Keep water spray away
from electric wiring or fatal electric
shock may result. Read warning tag
on electrical cord.

6. To protect the operator from elec-

trical shock, the machine must be
electrically grounded.  It is the re-
sponsibility of the owner to connect
this machine to a UL grounded re-

ceptacle of proper voltage and amperage ratings.  Do
not spray water on or near electrical components.  Do
not touch machine with wet hands or while standing
in water.  Always disconnect power before servicing.

CAUTION: Spray gun kicks back -- hold with both
hands.

7. Grip cleaning wand securely with both hands before

starting the cleaner. Failure to do this could result in
injury from a whipping wand.

WARNING: Flammable liquids can
create fumes which can ignite
causing property damage or se-
vere injury.

8.Oil burning appliances shall be in-

stalled only in locations where com-
bustible dusts and flammable gases
or vapors are not present. Do not
store or use gasoline near this ma-
chine.

WARNING: High pressure stream of
fluid that this equipment can pro-
duce can pierce skin and its under-
lying tissues, leading to serious in-
jury and possible amputation.

9. High pressure developed by these

machines will cause personal injury
or equipment damage. Use caution
when operating. Do not direct dis-

charge stream at people, or severe injury or death will
result.

10. Never make adjustments on machine while it is in op-

eration.

WARNING: High pressure spray
can cause paint chips or other par-
ticles to become airborne and fly
at high speeds.

11. Eye safety devices, foot protection

  and other protective clothing must
 be worn when using this equip-
  ment.

12. The spray gun should not be operated with the trigger

in the off position for extensive periods of time as this
may cause damage to the pump. Check to make sure
burner shuts off with spray gun closed.

13. Protect from freezing.

14. Protect discharge hose from vehicle traffic and sharp

objects.

15. To prevent serious injury, be certain quick coupler on

discharge hose has locked before using pressure
washer.

16. Before disconnecting discharge hose from hot water

outlet, turn off burner and open spray gun to allow
water to cool to 100°, then turn off pump motor and
water supply and open spray gun to relieve back pres-
sure in hose. This will prevent coil damage from ther-
mal expansion.

17. Do not allow acids, caustic or abrasive fluids to pass

through the pump.

18. Inlet supply water must be cold and clean fresh water.

19. The best insurance against an accident is precaution

and knowledge of the machine.

20.

LANDA will not be liable for any changes made to our
standard machines or any components not purchased
from 

LANDA.

21. Do not allow children to operate the pressure washer

at any time. 

This machine must be attended during

operation.

22. Do not overreach or stand on unstable support. Keep

good footing and balance at all times.

23. Follow the maintenance instructions specified in the

manual.

24. Do not operate this product when fatigued or under

the influence of alcohol or drugs. Keep operating area
clear of all persons.

WARNING

HIGH PRESSURE

STREAM CAN

PIERCE SKIN AND

TISSUES.

WARNING

RISK OF EXPLOSION:

DO NOT USE WITH

FLAMMABLE

LIQUIDS.

WARNING

USE PROTECTIVE

CLOTHING WHEN

OPERATING.

Warning:

Do not spay

machine or any

other electrical part.

                 Warning:

Must be plugged into properly
wired three hole grounded outlet 
that accomodates plug on power cord. 
Failure to comply could result in
electrical shock.

WARNING

KEEP WATER SPRAY

AWAY FROM

ELECTRICAL WIRING.

Summary of Contents for Platinum Series













































Reviews: