background image

7

Safety

gases or vapors are not present. Do not store or 
use gasoline near this machine.

6. Use No. 1 or No. 2 heating oil (ASTM D306) only. 

NEVER

 use gasoline in your fuel oil tank. Gasoline 

is more combustible than fuel oil and could result in 
a serious explosion. 

NEVER

 use crankcase or 

waste oil in your burner. Fuel unit malfunction could 
result from contamination.

7. Do not confuse gasoline and fuel oil tanks. Keep 

proper fuel in proper tank.

WARNING: Risk of injury. Hot 
surfaces can cause burns. Use 
only designated gripping areas of 
spray gun and wand. Do not place 
hands or feet on non-insulated 
areas of the pressure washer.

AVERTISSEMENT: Risque de 
blessures. Les surfaces chaudes 
peuvent causer des brûlures. 
Utiliser uniquement les zones de 

prise désignées du pistolet pulvérisateur et de la 
lance. Ne pas placer les mains ou les pieds sur des 
endroits non isolés de la laveuse à pression

8. Transport/Repair with fuel tank EMPTY or with fuel 

shut-off valve OFF.

CAUTION: Hot discharge fluid. Do 
not touch or direct discharge 
stream at persons or animals.

ATTENTION: Liquide de décharge 
chaud. Ne pas toucher ou 
décharger directement le jet vers 
des personnes ou des animaux

WARNING: This machine produces hot water and 
must have insulated components attached to 
protect the operator.

AVERTISSEMENT: 

Cette machine produit de l'eau 

chaude et doit comporter des composants isolés 
attachés pour protéger l'opérateur

9. To reduce the risk of injury, close supervision is 

necessary when a machine is used near children. 
Do not allow children to operate the pressure 
washer. 

This machine must be attended during 

operation. 

WARNING: Grip cleaning wand 
securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

AVERTISSE

MENT: Agripper la 

lance de nettoyage avec les deux 
mains avant de commencer. Le 
non-respect de cette consigne 
pourrait mener à des blessures 

causées par le mouvement violent de la lance

10. Never make adjustments on machine while in 

operation.
Be certain all quick coupler fittings are secured 
before using pressure washer.

WARNING: High pressure 
developed by these machines will 
cause personal injury or 
equipment damage. Keep clear of 
nozzle. Use caution when oper-
ating. Do not direct discharge 
stream at people and animals, or 
severe injury or death will result. 

AVERTISSEMENT: 

La haute 

pression générée par ces machines causera des 
lésions corporelles ou des dommages à 
l'équipement.
Se tenir à l'écart de la buse. Faire preuve de 
prudence lors de l'utilisation. Ne pas décharger 
directement le jet vers des personnes ou des 
animaux, car cela risquerait de causer des 
blessures graves ou même la mort.

WARNING: Protect machine from 
freezing.

AVERTISSEMENT: Protéger la 
machine contre le gel.

11. To keep machine in best 

operating conditions, it is 
important you protect machine 
from freezing. Failure to protect 
machine from freezing could 

cause malfunction of the machine and result in 
death, serious bodily injury, and/or property 
damage. Follow storage instructions specified in 
this manual.

12. Inlet water must be clean fresh water and no hotter 

then 90°F.

Landa PGDC Operator’s Manual  8.916-596.0 - BF

WARNING

RISK OF INJURY. 

HOT SURFACES 

CAN CAUSE BURNS

WARNING

HOT DISCHARGE FLUID:

DO NOT TOUCH OR

DIRECT DISCHARGE

STEAM AT PERSONS.

WARNING

TRIGGER GUN KICKS 

 BACK —  HOLD WITH 

        BOTH HANDS

WARNING

RISK OF INJECTION 

OR SEVERE INJURY

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

PROCTECT FROM

FREEZING

Summary of Contents for Pgdc5-3500

























Reviews: