Landa PE Operator'S Manual Download Page 4

LANDA PE  8.913-998.0

OPERA

TOR’S MANU

AL

 

PRESSURE 

W

ASHER  

4

IMPORTANT SAFETY INFORMATION

TRIGGER GUN KICKS 

BACK - HOLD WITH  

BOTH HANDS

WARNING

WARNING: Grip cleaning wand 
securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

RISK OF INJECTION 

OR SEVERE INJURY 

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure devel-
oped by these machines will 
cause personal injury or equip-
ment damage. Keep clear of 
nozzle. Use caution when oper-
ating. Do not direct discharge 
stream at people, or severe in-
jury or death will result. 

  

 10. To reduce the risk of injury, close supervision is 

necessary when a machine is used near children. 
Do not allow children to operate the pressure 
washer. 

This machine must be attended during 

operation.

 11.  Never make adjustments on machine while in op-

eration. 

 12. Be certain all quick coupler fittings are secured 

before using pressure washer.

WARNING

PROTECT FROM 

FREEZING

WARNING: Protect machine from 
freezing.

13.  To keep machine in best  
 

operating conditions, it is  

 

important you protect machine  

 

from freezing. Failure to protect  

 

machine from freezing could  

 

cause malfunction of the  

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol-
low storage instructions specified in this manual.

14.   Inlet water must be clean fresh water and no hotter 

then 90°F.

 15. Manufacturer will not be liable for any changes 

made to our standard machines or any components 
not purchased from us.

 16.  The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING

RISK OF INJURY 

FROM FALLS WHEN 

USING LADDER.

WARNING: Be extremely careful 
when using a ladder, scaffolding 
or any other relatively unstable 
location. The cleaning area 
should have adequate slopes 
and drainage to reduce the pos-
sibility of a fall due to slippery 
surfaces.

 17. Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

 18.  Do not operate this machine when fatigued or under 

the influence of alcohol, prescription medications,  
or drugs.

19.  Follow the maintenance instructions  
 

specified in the manual. 

Summary of Contents for PE





























Reviews: