background image

10

Maintenance

Troubleshooting

PROBLEM

POSSIBLE CAUSE

SOLUTION

LOW 
OPERATING
PRESSURE

Faulty pressure gauge

Install new gauge.

Insufficient water supply

Use larger supply hose; clean filter at water inlet.

Old, worn or incorrect spray nozzle

Match nozzle number to machine and/or replace with 
new nozzle.

Belt slippage

Tighten or replace; use correct belt.

Plumbing or hose leak

Check plumbing system for leaks. Re-tape leaks with 
teflon tape.

Faulty or mis-adjusted unloader valve

Adjust unloader for proper pressure. Install repair kit 
when needed.

Worn packing in pump

Install new packing kit.

Fouled or dirty inlet or discharge valves 
in pump

Clean inlet and discharge valves.

Worn inlet or discharge valves

Replace with valve kit.

Obstruction in spray nozzle

Remove obstruction.

Leaking pressure control valve

Rebuild or replace as needed.

Slow engine RPM

Set engine speed at proper specifications.

Pump sucking air

Check water supply and possibility of air seepage.

Valves sticking

Check and clean or replace if necessary.

Unloader valve seat faulty

Check and replace if necessary.

BURNER 
WILL NOT 
LIGHT

(continued on 
next page)

Little or no fuel

Fill tank with fuel.

Improper fuel or water in fuel

Drain fuel tank and fill with proper fuel.

Clogged fuel line

Clean or replace.

Plugged fuel filter

Replace as needed.

Mis-adjusted burner air bands

Readjust air bands for clean burn.

Little or no fuel pressure from fuel 
pump

Increase fuel pressure to specification and/or replace 
fuel pump. Test with pressure gauge.

Faulty burner transformer

Test transformer for proper arc between contacts. 
Replace as needed.

Disconnected or short in electrical 
wiring

All wire contacts should be clean and tight. No breaks in 
wire

Flex coupling slipping on fuel pump 
shaft or burner motor shaft

Replace if needed.

On-Off switch defective

Check for electrical current reaching 
burner assembly with burner switch on.

Heavy sooting on coil and burner can 
cause interruption of air flow and 
shorting of electrodes

Clean as required.

Improper electrode setting

Check and reset according to diagram in Operator’s 
Manual.

Fuel not reaching combustion 
chamber

Check fuel pump for proper flow. Check solenoid flow 
switch on machines with spray  gun control, for proper 
on-off fuel flow control.

Landa PDHW Service Manual  8.920-098.0 - AU

Summary of Contents for PDHW5-35624E













































Reviews: