background image

8.913-995.0 • Landa PC • Rev. 03/11

OPERA

T

OR’S MANU

AL    

PRESSURE W

ASHER 

 

4

IMPORTANT SAFETY INFORMATION

WARNING

KEEP WATER

SPRAY AWAY FROM 

ELECTRICAL WIRING.

WARNING: Keep wand, hose, and 
water spray away from electric 
wiring or fatal electric shock may 
result.

 

9. 

Do not spray water on 

or near electrical components. 

RISK OF EXPLOSION: 

DO NOT SPRAY 

FLAMMABLE LIQUIDS.

WARNING

WARNING: Flammable liquids 

can create fumes which can ig-
nite, causing property damage 
or severe injury.

WARNING: Risk of explosion — 
Do not spray fl ammable liquids.

10.  Keep operating area clear of 
all persons.

WARNING

EAR PROTECTION 

MUST BE WORN

WARNING: This machine ex-
ceeds 85 db appropriate ear 
protection must be worn.

WARNING

USE PROTECTIVE 

EYE WEAR

AND CLOTHING 

WHEN OPERATING

THIS EQUIPMENT.

WARNING: High pressure spray 
can cause paint chips or other 
particles to become airborne 
and fl y at high speeds. To avoid 
personal injury, eye, hand and 
foot safety devices must be 
worn.

 11.  Eye, hand, and foot pro-

tection must be worn when 
u s i n g   t h i s   e q u i p m e n t .

TRIGGER GUN KICKS 

BACK - HOLD WITH 

BOTH HANDS

WARNING

WARNING: Grip cleaning wand 
securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

12.  To reduce the risk of injury, 
 

close supervision is necessary 

 

when a machine is used near 

 

children. Do not allow children 

to operate the pressure washer. 

This machine must be attended during operation.

RISK OF INJECTION 
OR SEVERE INJURY 

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure devel-
oped by these machines will 
cause personal injury or equip-
ment damage. Keep clear of 
nozzle. Use caution when oper-
ating. Do not direct discharge 
stream at people, or severe in-
jury or death will result. 

13.  Never make adjustments on 
machine while in operation. 

 14. Be certain all quick coupler fi ttings are secured 

before using pressure washer.

WARNING

PROTECT FROM 

FREEZING

WARNING: Protect machine from 
freezing.

15.  To keep machine in best 
 

operating conditions, it is 

 

important you protect machine 

 

from freezing. Failure to protect 

 

machine from freezing could 

 

cause malfunction of the 

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol-
low storage instructions specifi ed in this manual.

 16.  The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING

RISK OF INJURY 

FROM FALLS WHEN 

USING LADDER.

WARNING: Be extremely careful 
when using a ladder, scaffolding 
or any other relatively unstable 
location. The cleaning area 
should have adequate slopes 
and drainage to reduce the pos-
sibility of a fall due to slippery 
surfaces.

 17. Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

 18.  Do not operate this machine when fatigued or under 

the infl uence of alcohol, prescription medications,  
or drugs. 

19.   Inlet water must be clean fresh water and no hotter 

then 90°F.

 20. Manufacturer will not be liable for any changes 

made to our standard machines or any components 
not purchased from us.

 21.  Do not allow acids, caustic or abrasive fl uids to pass 

through the pump.

 22. Never run pump dry or leave spray gun closed 

longer than 1-2 minutes.

 

Follow the maintenance instructions speci-
fi ed in the manual. 

Summary of Contents for PC3-2400



























Reviews: