background image

9

Safety

22. Never run pump dry or leave spray gun closed 

longer than 1-2 minutes.

23. Machines with shut-off spray gun should not be 

operated with the spray gun in the off position for 

extensive periods of time as this may cause 

damage to the pump.

24. Protect discharge hose from vehicle traffic and 

sharp objects. Inspect condition of high pressure 

hose before using or bodily injury may result.

25. Before disconnecting discharge hose from water 

outlet, turn burner off and open spray gun to 

allow water to cool below 100ºF before stopping 

the machine. Then open the spray gun to relieve 

pressure. Failure to properly cool down or maintain 

the heating coil may result in a steam explosion.

26. Do not overreach or stand on unstable support. 

Keep good footing and balance at all times.

27. Do not operate this machine when fatigued or 

under the influence of alcohol, prescription medica

-

tions, or drugs.

28. Use only kerosene, No. 1 home heating fuel, or 

diesel in burner fuel tank. If diesel is used, add a 

soot remover to every tankful.

WARNING: Do not spray machine or 

any people, animals or electrical 

parts.
AVERTISSEMENT: Ne pas vaporiser 

sur la machine ou les gens, les 

anomaux ou les pièces électriques.
ADVERTENCIA: No rocíe la 

máquina ni a las personas, 

animales o partes eléctricas.

Follow the maintenance instructions 

specified in the manual.

Landa MHC  9.800-950.0 - BM

WARNING

DO NOT SPRAY 

MACHINE OR ANY 

PEOPLE, ANIMALS OR 

ELECTRICAL PARTS.

Summary of Contents for MHC3-24324


























Reviews: