25
Section 5: Maintenance & Lubrication
4/24/12
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Table of Contents
5.
Install the new short skid shoe (#2) to the back left
deck corner as shown with 3/8"
-16 x 1 1/4" GR5
plow
bolts (#2), flat washers (#6), lock washers (#5), and
3/8" hex lock nuts (#4). Torque lock nuts (#4) to
31 ft. lbs.
6.
Install the long skid shoes (#1) to the remaining three
deck corners with 3/8"
-16X1 1/4" GR5
plow bolts (#2),
flat washers (#6), lock washers (#5), and 3/8" hex
lock nuts (#4). Torque lock nuts (#4) to 31 ft. lbs.
7.
Raise cutter up and remove support blocks.
Hydraulic Maintenance
!
DANGER
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be treated by a
doctor within a few hours or gangrene may result.
One of the most important things you can do to prevent
hydraulic system problems is to ensure that your Skid
Steer reservoir remains free of dirt and contamination.
Use a clean cloth to wipe the hose ends before attaching
them to your Skid Steer. Replace the filter element for
your Skid Steer’s hydraulic system at the prescribed
intervals. These simple maintenances will go a long way
to prevent occurrence of hydraulic problems.
Land Pride Standard Skid Shoe Bundle 326-027A
Item Part No.
Part Description
1
312-602D SKID SHOE, 1/4" x 2"
2
326-276D DECK RUNNER LH REAR, 1/4" x 2"
3
802-466C PLOW 3/8-16X1 1/4 GR5
4
803-013C NUT LOCK 3/8-16 PLT
5
804-013C WASHER LOCK SPRING 3/8 PLT
6
804-012C WASHER FLAT 3/8 SAE PLT
Land Pride Heavy Skid Shoe Bundle 326-028A
Item Part No.
Part Description
1
326-343D SKID SHOE HEAVY, 3/8" x 3"
2
326-344D SKID SHOE HEAVY SHORT, 3/8" x 3"
3
802-466C PLOW 3/8-16X1 1/4 GR5
4
803-013C NUT LOCK 3/8-16 PLT
5
804-013C WASHER LOCK SPRING 3/8 PLT
6
804-012C WASHER FLAT 3/8 SAE PLT
Long Term Storage
!
DANGER
Do not modify the Rotary Cutter without authorization from
Land Pride. Unauthorized modifications to the cutter can
result in the cutter not performing properly and/or cause
serious injury or death.
!
DANGER
Always secure cutter deck in the up position with solid
supports before servicing underside of cutter. Never work
under equipment supported by hydraulics. Hydraulics can
drop equipment if controls are actuated or if hydraulic lines
burst. Either situation can drop the cutter instantly even when
power to the hydraulics is shut off.
!
CAUTION
Store cutter with hitch plate in the upright position. A hitch plate
that is stored folded down against the deck can tip up easily
resulting in serious injury to the body.
Clean the Rotary Cutter at the end of the working season
or when the cutter will not be used for a long period.
1.
Clean off any dirt or grease that may have
accumulated on the cutter and moving parts. Scrape
off compacted dirt from the bottom of the deck and
then wash the surface thoroughly with a garden hose.
A coating of oil may also be applied to the lower deck
area to minimize oxidation.
2.
Check blades and blade bolts for wear and replace if
necessary. See “Cutter Blade Maintenance” on
page 23.
3.
Inspect for loose, damaged, or worn parts and adjust
or replace as needed.
4.
Repaint parts where paint is worn or scratched to
prevent rust. Ask your dealer for Aerosol Land Pride
touch-up paint.
5.
Replace all damaged or missing decals.
6.
Lubricate as noted in the Lubrication portion of this
section starting on page 26.
7.
Store the Rotary Cutter in a clean, dry place. The
deck should be positioned on a flat surface to suitable
Skid Steer hook-up height. Ensure that the main
frame is stable. Use auxiliary supports or posts if
necessary to prevent the possibility of the unit tipping
over. Store hitch in the upright position.
Land Pride Touch-up Paint
Part No.
Part Description
821-011C
PAINT LP BEIGE AEROSOL SPRAY CAN
821-002C
PAINT GP BLACK SPRAY CAN